Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
On a custom board using the nRF51822, with SDK 11.0.0, SD s130 and gcc, I'm seeing the following stack trace when doing some TWI operations to program an accelerometer:
...
I have to send a data to more units, i have found problems with multiple ACK return signals (I think this is the problem).
So i'm trying to send data with no ACK.
For this...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
Hi.
I've played around with the android application (based around google gatt example, but used in gatt server -mode).
How is the example expected to be handled? In...
Hello everyone,
I am currently trying to make simple exchanges with an NFC chip using SPI.
Configuration is: nRF52 on dev board 10040 with example from SDK12 located...
Hi,
I have such code:
static buf[9] = {initializers};
for(i =0;i <9;i++){
while(app_uart_put(buf[i]));
}
I always get "0" before the actual buf content and the...
Hi
I've implemented a peripheral with bonding support by the peer manager. Additionally the device should scan for bonded devices by using a whitelist. I used the function...
Hi,
I'm trying to compare two RC networks by using GPIOTE, PPI, a Timer and the comparator to measure the time needed for a charge and discharge cycle for each of the networks...
Is it possible for one Arduino Uno to have a BLE nRF8001 module and a nRF24L01+ module wired to it (allowing each module to communicate simultaneously)? According to the wiring...
We are trying out the new nRF5x SDK v12 and it looks like the previously working ble_app_hids_mouse example is broken now.
It compiles successfully, but as soon as we try...
I have observed that the Radio Notification from ble_radio_notification.c becomes inverted sometimes. I saw this post about the same problem:
devzone.nordicsemi.com/.....
I would like to use nRF5 SDK for IoT with some functionalities (e.g. SEGGER RTT) from nRF52 SDK. Can I just copy desired modules to my SDK for IoT and suppose it'll work?...
Hello,
For some industrial reasons, I need to store the passkey in the flash of the nRF5 during production and retrieve it at run-time.
I would like to know if there...
Hi,
for our prototyp we use a NRF52. When i flash the device, it will always be go in sleep mode after a duration of time and stay in there.
Is there an interrupt which...
