When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I have a sensor HTS221 that I would like to power from an nRF52832 I/O to allow programmatically resetting the sensor. Looking at section 20.4.1 GPIO Electrical Specification...
We have bots (what I'm calling our device for this question) that play both the peripheral and central role depending on their context (not unlike the relay example; except...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
HI,
Currently I try to run example/iot/tcp/client in nrf51 iot sdk on nrf51-dk board. Then on server side, I use "ping6" command to test the data sending and receiving...
Hi, Very happy to note that you are planning to release source for nRF Connect for Desktop soon. Do you have an updated timeline on that?
Also, I am trying to use pc-ble...
Noticed this for gcc with -0s optimization an application fail to save a bonding data. It is caused by byte alignment of
static uint8_t buffer_memory[(n_blocks) * (block_size...
Hello everybody,
I am a newbie, and I tried to follow this tutorial to set up my laptop for development.
Everything works until I went to the step "Import existing Eclipse...
Hi,
I am currently writing the firmware of one of our products that will be produced in mass market, and now my goal is to have a unique BLE device name for every sample...
I am trying to study the docs for GPIOTE in SDK12 and see various sections for GPIOTE. What are the differences between: Driver , Abstraction , Handler and Handling Library...
I'm following the tutorial Development with GCC and Eclipse
I could compile and flash existing project that attached to tutorial.
Now I can't understand what to to while...
Q1: how to do network commission? do we have to use an Apps to do commission linke CSRmesh? or it is already in a same network if we configure all nodes use the same access...
I have been using pc-ble-driver in Linux (downloaded and compiled from github here - github.com/.../3316c0c306257a825168751964f814cb95fc0d74) with our custom C++ application...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
Hi All,
I am using nRF51822 for my application.
how to change the App timer Interval dynamically means i have to change the timer interval before timeout.