nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I want to confirm with Nordic staff that the MBR compares the new bootloader with the one it will replace when executing SD_MBR_COMMAND_COPY_BL. It seems that after a comparison...
Hello
Just few quick questions. What happens to the S110 Softdevice after the APP_ADV_TIMEOUT_IN_SECONDS period?
I'm using the nRF51 DK and the ble UART example and I...
As I am using nRF51422 EK (Evaluation kit), would like to know how to test with BT2.5 or lower version. Is this has backward compatibility. As when I give option of FLAG other...
Hello
I'm having difficulty in executing an GPIOTE interrupt during a BLE connection event with the nRF51 DK. The interrupt I have works fine when the softdevice is advertising...
If I set the centrals connection intervals values higher as a specific value it won't any longer find/connect/enable notifications on my peripheral.
0x00A0/0x0050/ 400...
After running the advertising_start () function in the sample software.
I set the breakpoint by Keil MDK-ARM v5 and stopped executing.
Afterwards, reset is generated!!
...
Hi,
I am using a gpiote interrupte handle function to send a notification to the master,but I find when the sd_ble_gatts_hvx() function is used,the interrupte handle function...
I have successfully completed dfu using android app, but if anyone can help me with example program so that i can perform dfu using program instead of using toolbox app, please...
On the XLR2 chipset I am seeing that if the RTS output follows the state of the CTS input.
When I load the same firmware in a XLR then RTS does not follow CTS
Hi, I am evaluating the use of ESB(without Ack) and BLE as a possible solution for my project since i have no use of Ack and in Gazell it is mandatory to use Ack. I had heard...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
I'm drawing schematic with nRF51822 internal LDO. I'm wondering what is the regulated LDO output from nRF51822. I need to connect that with peripherals in stable...
We are using ANT with the nRFgo motherboard as base station and want to broadcast a signal over the largest range possible (> 100 m) to several mobile devices using the Dynastream...
I am designing a ECG monitor device. The data rate is less than 50kbps. I was planning to use BLE for the device design. But I read some documents that say BT classic is a...
