I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
For a device like the nRF9160 Feather, you need a second USB to UART device for listening to the modem traces. When I go to select the Terminal Serial Port under Advanced...
I was trying to set up partitions on a nRF5340 DK so I can use MCUBoot, settings, and littlefs but am getting this error when flashing the dk:
The output Zephyr.dts has...
Dear Support,
I encounted an issue when tried to connect with complicated wifi network recently.
The error info is as follwing.
"WPA: 4-Way Handshake failed - pre-shared...
Hi,
we use our code for beacons for very long time now. Unfortunately producer changed chip.
We were using NRF51802QF with SoftDeviceS130.
Now the chip is NRF52810QCAA...
I am receiving the following errors: [00:00:00.117,187] <wrn> bt_hci_core: opcode 0x2027 status 0x12 [00:00:00.118,133] <err> bt_id: Failed to add IRK to controller Which...
Hi,
I am new to board programming. I have a custom board with nRF52881. There is no USB port on the board to connect it directly to the PC. How can I connect the board...
Hi,
I see in the GNSS documentation for the nRF52840 that the GNSS modem performs scheduled downloads in Periodic Navigation mode, and from some testing, I found the download...
I am using nRF52832 Board for DFU. I want to implement static partition required for dfu operation. I would like to know that where shall I save the pm_static.yml file and...
The ActiveHardwareFaultsEnum supports a "TamperDetected" hardware fault, which is of interest for our product.
Using the general diagnostics server, it is possible to set...
If I use zb_zdo_mgmt_lqi_req() for dst_addr = local short address is the response resolved internally?
I have an application where I need to locate certain zigbee devices...
Dear Nordic support team,
We are using the SDK v2.6.1 to build targets for nRF52840 chips, and are using multiple configurations defined in a CMakePreset.json file.
It...
Hello!
I am currently running into throughput problems while using the Nordic Uart Service (NUS).
I am building a project for a peripheral and wanted to test the possible...
Hello,
We are implementing BLE FOTA for nRF52832. For that trying to load nrfutil tool. Its downloaded from official website. python is also installed successfully. when...