Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello everyone,
I am working on a project based on nRF Connect SDK v1.7.1 that I want to move to the new SDK v1.8.0. But I'm experiencing problems when building the project...
Hi We'll be adding to a design that uses libuarte/UART0. I've tested/run the example code and it's fine. Changing/swapping index from UARTE0 or 1 works fine as does reassigning...
Hi Sir/Miss,
I use SDK 17.0.2 version and softdevice s112 7.2.0 version to develop in nrf52810.
And, I base on this project (NUS with static passkey) which imports CTS_C...
Hi,
In nRF_Connect_SDK's OpenThread's Coap_Client sample, I want to implement the role of both client and server on a single node.
Also instead of sending messages to...
I'm trying to implement the FTMS fitness machine service with the Kinomap app, similar to zwift. using as base the code of the ble_app_rscs of the library nRF52 together with...
Hi,
I understand that Attribute protocol supports commands, requests, responses, notifications and indications.
Can you please tell me if those packets are sent with the...
Hi,
I'm new to nRF52840 Dongle development.
We use some nRF52840 Dongles (packed in a machine) with pc-ble-driver-py for transferring data through BLE.
I can not share...
Hi,
I'm using the flashlog on my nRF52840 to log events. I have an external RTC which I read when logging each event in order to timestamp the event. My RTC code writes...
I am trying to set up a project that uses MCUBoot and puts the secondary slot into QSPI External Flash. I'm using NCS 1.7.1 with VS Code. I've followed numerous posts on these...
I am currently evaluating the differences between nRF52811 and nRF52810. I am still using the nRF5 SDK.
One difference is in the nRFInitialize function in the startup code...
Hello,
In my application (using sdk 16.0.0) I have a bootloader that allows to upload a new firmware through either BLE or UART. The Bootloader is initialized as usual:...
Hi All!
I have a problem running simple PWM output on NRF5340 board. I have a following code:
Now what i'm trying to achieve is to get 50% of duty cycle with frequency...
Hi there,
This should be straight forward but has me stumped. I'm trying to add BLE to my CAF based application and can't do and recreated the same problem with the samples...
Hello, I have a two part question with regard to SPIS setup time when exiting low power mode on an nRF52840.
We are using the SPIS peripheral on an nRF52840. General guidance...
