Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello,
The following code was embedded in main function, the sdk version is 15.2.
the debug console show as below:
My question is , why string "This is a string...
Dear all,
after some customs problems I hope I finally will receive my Thingy 91 tomorrow. I have already installed the toolchain and done some readup on the device for...
I am attempting to build the new alexa_gadget example that is included in the nRF Connect SDK.
Environment information:
Windows 64-bit
nRF Connect v3.6.0
nRF Connect...
Hi everybody,
I think have a problem which involve writing on the external memory of the nrf52840, what I want is when I receive data from the NUS service I want to store...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hi,
The system has an nRF52840 as a BLE USB Dongle plugged to a PC, and connected by BLE to another device (another nRF52840).
I measure the latency time between the...
Hello everyone.
I made my own board with nrf2840 and wanted to use the CC310 module for encryption.
I uploaded an example from the SDK to my board and in the debug I see...
Hi,
I am a newbie to nRF devices. I have different sensors connected to TWI,SPI,ADC etc. and need to send these data to a cellphone through BLE. Does anyone has a sample...
Hello,
I'm starting to investigate using the nRF52833 as part of my design and i wanted to clarify the specification in the datasheet. it states the following:
Does...
Hi,
When upgrading a project from ncs 1.3.0 to 1.4.0, the clock_control_on() call behaves different; It always returns -EPERM. Did the API change?
The call is used as...
Hi everyone,
I want to modify the USBD example.
In the USBD example there's a mouse but I don't have to work with a mouse.
I want to transfer data from ADC to PC. How...
Hi, I am using the Nordic nRF52832, with v15.2 of theSDK, and would like to use "nrf_sdh_freertos_init" to implement multilink. I refer to example "ble_app_multilink_central...
I have beacon (ble_app_beacon) transmitting every 40...50 ms, nRFConnect shows adv interval is ~44 ms, so it receives ~22 msg/sec. My beacon listener gets only 10...12 msg...
Hi,
I have simple test firmware that simply connects to the network and goes into PSM sleep, it works perfectly well on the nRF9160DK but the Thingy 91 is refusing to connect...
