I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
nRF52832 will restart accidentally, I have checked code, but I haven't fixed it so far;
Because restart is random, it is hard to reappear;
my question is
1, How do I...
Hi Sir,
My project need LESC & AES-CMAC function, then I enabled below CONFIG in sdk_config.h :
NRF_CRYPTO_BACKEND_MBEDTLS_ENABLED
NRF_CRYPTO_BACKEND_MBEDTLS_ECC_SECP256R1_ENABLED...
Hi,
So I am trying to configure the stdout console to use UART1 by default. Using the NrfConnect menuconfig in Segger emStudio I can set it to use UART1 with the following...
Hello !
I have read in DevZone, but still not sure regarding nRF52832 .
For nRF52832 and page size 4k, and regarding only writing zero-bits.
Can I in same page perform...
Hi team,
Here is the previous ticket
https://devzone.nordicsemi.com/support/234693
One of my customer TMC is using our nRF52810 in a BLE key project for central role...
When in dfu mode (with usb dfu enabled) if we jump to application via "
nrf_bootloader_app_start" there seems to be an issue where the firmware locks up and doesn't start...
Hello
my setup is a nrf52840, the sdk15.3, Softdevice s140.
is there a possibility, maybe with freertos, to to run two seperate applications like two threads.
In the...
Hi,
I'm trying to implement a slow timer which is supposed to be triggered about every 30 minutes or even less frequent, but I'm kind of clueless how to solve this issue...
from which antenna these values were derived resp. measured? e.g. there is a pcb antenna and a hirose u.fl connector available on pca10040... examples/ble_peripheral/ble_app_eddystone...
hi,
The software version is nrf5SDKforMeshv310src and nRF5_SDK_15.2.0_9412b96
I use five nRF52832 nRF52 DK. client * 1, server * 4, provisioner by android phone.
examples...
Hi can you help to configure nrf52840 DK board to measure power consumption with keysight n6705C. In manual is described with ammpermeter and oscilloscope. Keysight n6705c...
Hi, I'm new here so please let me know if any additional information could help.
We are in need of encoding speech on a nRF52840 and are working in Opus and are having trouble...
Im getting this error any idea how to solve it this are configs.
Loading solution lte_ble_gateway.emProject
Executing load commands
/usr/local/Cellar/cmake/3.15.2/bin...
If the only supported method is through the PC-based nRF Connect Programmer GUI application, how is a system based on nRF91 its modem firmware once deployed in the field ...
