Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi, I have seen a few similar questions to this but the answers weren't too clear...I am trying to use both the long button push and the button push actions to generate separate...
Hello,
I have a Raytac MDBT50Q-RX USB dongle that I want to evaluate.
The dongle comes with Raytac's own test firmware.
In order to evaluate it for my purpose, I wanted...
I am very new begginer and dont know where to start about nordic nrf52832 chip. Started a week ago with downloading SDK and playing with examples in it.
I in specific need...
This is the structure.I am using bitfields here, even if i don't the problem still exists.
struct CODE_T
{ uint32_t guest_code_start_time; uint32_t guest_code_end_time;...
Hi,
Lior Neumann and Eli Biham found a vulnerabilitiy in BLE secure connections, to which CVE-2018-5383 was assigned.
Is the S132 SoftDevice affected by this vulnerabilitiy...
Hi Everyone
My requirements are as follows
1. I am running 4 tasks using free rtos in which one measures the ADC , 2nd sends the adc data over BLE and 3rd check if the...
hello
I am using sdk 15.3 example code of DFU (secure_boot loader \ pca10040_ble)
I want to debug code but i can not.I getting error like that "Error Flash Download Failed...
Hello,
I have been using this method for a while now and everything seemed to work. But for one of my device the method returns the error 0x3400. I wanted to know where...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
Hi there,
I want to do scanning existing networks and for these goals, I need to enable Commissioner on Commissioner side. I use the otCommissionerStart function but when...
I am looking for an example that can work with Android 6 and higher
Current examples on Github have compilation problems probably using older gradle.
The application need...
Hi,
I'm wondering why SES 4.18 requires an entire rebuild of an application each time a project is (re)opened? I would have though it would perform an intelligent incremental...
Hi,
I am trying to modify the ble_hids_mouse example project to convert the device into a vendor defined HID device. I need to send 64 bytes of custom sensor data (which...
Hello,
I am migrating my code based on Mesh SDK V2 to V3.1.0. on nRF52840. The filter based on the uuid used in functions "prov_helper_provision_next_device" and "uuid_filter_compare...
