the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I am not sure if this is the right place to open up a thread about a zephyr HCI firmware issue. Since Nordic also contributes to zephyr I'm putting up this question...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi All:
When I simulated PWM by GPIO, the output current noise was shown like the picture below (red circle area):
Cause it will lead to a loading issue in the backend...
I want to implement a long write. The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi Nordic team,
I have 2 nRF52840 DK boards.
I followed the steps mentioned in the below link, I am able to Transfer the DFU archive over serial with nrfutil(LED keeps...
I want to enable the Logger Module to have the high default severity of Error and then be able to enable lower level severities on an individual module for debugging. Is this...
Hardware used: 2 nRF52480 DK boards
I am running nRF5_SDK_15.0.0_a53641a\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput example, I want to increase...
I read zephyr official document of nrf52810 support：
http://docs.zephyrproject.org/boards/arm/nrf52810_pca10040/doc/nrf52810_pca10040.html
It describes like this : ...
Hello,
I just got my nRF52832 DK and am following the Getting Started at the Infocenter to get familiar with it. Running Ubuntu 16.04 and all the latest Nordic tools (SDK...
Greetings, I got a nRF52832 DK and only just found out that Smart Remote 3 is probably more what I'm looking for. It should be no problem to set it up on the DK with an appropriate...
I am working on a custom board based on nrf52810 that my client provided. In this board the accelerometer (Bosch BMA250E) power has been controlled by the PIN 9. However when...
Hi, everyone
I have some problems to make the Image Transfer Demo APP work
I have read the content of the website( https://github.com/NordicPlayground/nrf52-ble-image...
Hi,
I have 2 devices: one nrf52832 and one nrf52840 dongle. After enabling PHY feature (see the following code) in nrf52832, I tried to connect it using the dongle in the...
Hi,
I got the following hardfault when running sdk 14.2, nrf52832. Since the address shows it locates in softdevice...I do not know why. May you please give me tip? Thanks...
