Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
What is the max timer frequency that the nrf52840 can handle in counter mode?
I see that the timer runs at max 16Mhz when in timer mode, is it possible to get 32Mhz...
Ok I’m new to ARM / Nordic and Bluetooth but after a bunch of reading I downloaded SES and the Mesh SDK and got the light switch demo to both compile and run on a few boards...
I'm looking for where the compiler is for the nRF52832....
I just need to compile code, and copy the binary to the device....do you have any pages which show, step by...
hai. I got thingy 52 from Nordic tech tour. now i would like to reconfigure it. for enabling all its sensor into RTOS(real-time operating system apache mynewt) with the nrf52...
I want to implement a ready line for SPI and I noticed nordic has similar code in your sdk: components/serialization/common/transport/ser_phy/ser_phy_spi_slave.c.
However...
Hi,
I am trying to send data to server using ESP8266 WiFi module interface with nRF52832 DK board via UART interface. My problem is when i sent AT command to ESP8266 it...
Hi,
I have a project with 52810, I met below build error when compiling dfu project:
.\_build\nrf52832_xxaa_s132.axf: Error: L6366E: uECC.c.o attributes are not compatible...
Hi
Now I'm using nRF52810 base on SDK v14.1 and I want to do the OTA for it. When I combile the bootloader project, I get so many error "No space in execution regions....
I just want to change the Advertising interval min and max values in ble_gap.h file in meta wear RG
so do I have to change firmware code or is there any other way to deal...
In the eclipse setup here
https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development-with-gcc-and-eclipse
It give two links to example eclipse projects...
I can see that we can use APPROTECT to disable reading of the flash.
This seems to be reversible using: nrfjprog -f NRF52 --recover, which will erase the flash and allow...
I used SDK nRF5_SDK_14.1.0_1dda907.
I added cycling speed and cadence service of BLE and bicycle speed and cadence of ANT+ in ble_ant_app_hrm example of multiprotocol. ...
First - thanks to those who answered my question about the Segger Embedded Studio code size limit. It appears to have be fixed when I switch the build configuration from ...
I would like to use a Bluetooth protocol analyzer for sniffing traffic in my Mesh network. I need to input the devkey(s), netkey, and appkey to the protocol analyzer software...
