Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hello, I've downloaded the lastest SDK (ver. 12) and the installer is only valid for keil 4.
Is it any option to have this SDK working on keil uvision 5 ?
Thanks in...
Hello all,
I just bought the nRF52(PCA10040) DK and programmed the s132 version 3 soft device using nRFgo Studio. Using IAR, I compiled and downloaded the UART example...
Hi,I'am try to update the bootloader. But it stop at 1%. I don't what I miss.
james_boot.hex
james_bootloader.zip
Log 2016-09-06 11_36_54.txt
Dfu_bootloader_via_hex...
hello,
I'm using S132/nRF52/SDK11.
I start a firmware development based on Nordic UART example, I kept the BLE NUS part (I loop back the data received over BLE) and...
Hi All,
Just noticed SDK12 was released last week, with build in support for S132, v 3.0.0. Judging from the compatibility matrix and notes, it looks like it removed support...
Hello,
I'm trying to set a new environment with the SDK12 that'll be less cringy than the one I was running under the previous one.
Basically, what I want is a workspace...
Hi
Using an nRF52832 and SDK11, I have the following issue:
I want to use button 0 with a regular push for functionality and a long press to go to sleep. The detection...
Hi, I'm trying to move from nRF5_SDK_11.0.0_89a8197 to nRF5_SDK_12.0.0_12f24da and faced an issue. I have build error in
....../nRF5_SDK_12.0.0_12f24da/components/libraries...
Hi@all,
i'm trying to connect to a BTLE Printer (printer -> peripheral) from my central (nrf51822 board). But i cannot use the standard discovery examples because i cannot...
Hello, I have pca10001 board and I would like to read an analog input from ADC.
Is there any complete example which I can test using potentiometer ?
Thanks
I'm trying to write some data to flash memory (32 bytes) every 1 minute. the data are not NULL but then I noticed that sometimes (not always) the pstroage module write zeros...
Hi,
I am programming and debugging an external customised board by following the DK manual and the below link:
electronut.in/.../
I use the interface P20 instead of...
Dear all
I want to add the static pin to my project(s110 stackV8.0, based on SDK10), add the follow code to gap_params_init:
uint8_t passkey[] = STATIC_PASSKEY;
m_static_pin_option...
Dear all
Good day!
I want to develop the Android APP to received the BLE's ad raw data(which is dynamic change). Which API should I called to get the raw data? And should...
