I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Since https://github.com/nrfconnect/sdk-nrf has disabled issues, this is an assorted list of problems/limitations with the lte_net_if library ( https://github.com/nrfconnect...
Hi All,
I want to do dfu over uart with secure bootloader, am using nrf52840-DK, nRF5_SDK_17.1.0_ddde560 SDK and segger embedded studio V8.10.
compiled and flashed secure_bootloader_uart_mbr_pca10056_debug...
I use DWM3001C chip,it has a nrf52833 mcu inside.when i call ble_init() in main.c.it report error:
peer_manager_pds: Could not initialize flash storage. fds_init() returned...
Hi Team, I'm trying to port the acconeer project that worked on the old one NCS v2.2.0 to new NCS v2.5.2 and ran into a problem with the difference
c:/ncs/toolchains/c57af46cb7...
I am trying to use libmodem in a bare-metal app on a 9151dk, but nrf_modem_init() is hanging (not returning). What conditions can cause this? The issue looks a little like...
Hi there.
Right now, I'm facing the issue that I want to use the camera OV7670 with the nRF52833.
I don't know how to start or what example I can take as a base to start...
Hi,
I am using EVB of RAYTAC MDBT50Q-DB (nrf52840 module) for power consumption testing,
I'm running a zephyr application on it, to debug power consumption issues, using...
I have an application where I would like to use ACLK at 12.0 MHz to drive the I2S MCLK signal and create an atypical audio sampling rate (46875 samples/sec). If ACLK is at...
Hello!
Using SDK v2.6.1 and the nRF5340 Audio application, I want to use an external button as button5 instead of the one that is on the board.
I noticed that if i change...
Sometimes I just want to compile a single file for an nRF Connect project with VS Code and the nRF Connect extension. This sometimes fails because an include file isn't found...
Hi.
I am updating an nrf9160 B1 project on a custom board in SDK 2.1.0 to SDK 2.5.3, and I am running into a problem when building. This error does not show up when building...
Hi,
Hello, I have a project that's working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a so many threads on this...
Hi DevZone!
I'm currently developing a device that has several hardware actuators and I've implemented 2 OnOff Models each belonging to an element. But right now I'm having...
Hello there!
I'm trying to enable secure boot via CONFIG_SECURE_BOOT and am currently getting the following error:
I'm using zephyr via sdk-nrf v2.6.1
Searching the...
