I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
we don't seem to have power numbers for the 54L, but in the 5340 datasheet it shows the LFXO (0.16uA) used less power then the LFRC (1 uA).
Is that true with the NRF54L...
Hello, I am working on a project using a custom hardware configuration based on nRF5340 and nRF7002 similar in configuration to the nRF7002-DK, except without the on-board...
Hi!
We're building a project for the nRF54 where we want to run an external library on the FLPR core.
Right now we have a prototype PCB with a module from Fanstel on it...
Hello,
I am using configUSE_TICKLESS_IDLE with RTC2 setup for FreeRTOS tick, occasionally I am seeing the asserting in task.c at line configASSERT( ( xTickCount + xTicksToJump...
Hello everyone,
I’m fairly new to Android development and currently building a BLE app using Kotlin in Android Studio. So far, I’ve managed to implement scanning, connecting...
After a fresh installation of NCS 3.0.2 SDK and toolchain via the VScode extension, all west modules are reporting modifications:
PS C:\ncs\v3.0.2\zephyr> west status =...
HI DevZone,
I am trying to add the coded phy features in Peripheral_Uart and Central_Uart examples of NCS. I hope Coded phy features are successfully added into Peripheral_Uart...
Hello,
To finaly adjust the inside crystal capacitor at the end of production, I need measure the LFXO and HFXO frequencies signals to fine tuning. How should I do ?
Best...
Hi Nordic DevZone !
I'm facing an issue that I cannot manage to fix by myself.
So here is the brief: I'm trying to create a BLE beacon that will send some analysis results...
We are working with the nRF7002-DK board and need to measure and minimize power consumption. We are using Wi-Fi in our application and currently working with the sample nrf...
Hi,
I want to measure the current draw of the MCU only on the nRF52840DK while I am running my custom code. I want to exclude the current draw of all components except for...
Hi,
I’m currently working with the nRF52833 together with the nRF21540 Front-End Module (FEM). I have configured the FEM to provide a gain of 10 dBm. I have a few questions...
I want to use Nordic 52840 DK (Bulb FW) as DUT to setup Matter Certification test.
I have completed below steps:
1. Flash Raspberry Pi （Ubuntu Server 24.04.2 LTS (64-bit...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
Hi,
does the Azure functionality in the nrf connect SDK support the SAS authentication? I need to connect only with the SAS key, and as far as I can see, that's not possible...
