I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
I have a peripheral, that should connect to a central automatically. The problem is, there might be multiple
centrals with the same target name available and the central...
Hello, I made a new project at SEGGER for nRF5340 and in the first step before do any development I face with the attached error! The file it asked doesn´t exist !! Could...
Hello DevZone support team!
We are right now doing GCF certification of a device based on nRF9160 and need some urgent support from You!!
Attached is an excel sheet with...
Hi, I need more information about the GPS Chipset used in NRF9160 SIP or give me the name of this GPS module, so I can find its spec on the internet. Thanks in advance
I'm trying to activate because I want to use the HKDF of the nrf_oberon library. But when I try to compile with CMake and the target zephyr_final I get the following error...
Hello,
I am currently trying to program the nRF52832 to be able to receive data from a heart rate sensor. The sensor uses I2C communication and has an additional two pins...
Hi,
I am using this SDK: nRF5_SDK_15.2.0_9412b96 with NRF52840.
Having a disconnection issue where the device disconnects after one hour, If there is more devices connected...
Supposing that I broke off the nRF current measurement pin connector on the nRF9160dk - what are my options i.e. are there other pins that can be made available for the purposes...
Hi support team,
i'm using nrf dongle 52840 to update firmware for orther device, but somethime i can not able to access to send some command until hard disconnect from...
Hi,
I want to connect to Google Cloud IoT and for that I would like to generate the needed credentials on the nRF9160.
I need these ones , but the private key should...
Hi,
We have a strange issue. We have got two nrf52840DK(PCA10056, 2.0.0, 2019.47). The nrf52840DK board is not getting powered up after the board rested in off for a long...
I am following example in https://docs.edgeimpulse.com/docs/nordic-semi-nrf5340-dk but I cannot connect nrf5340 to EdgeImpulse studio . When I connect device via usb cabel...
Hi,
We are developing an IoT sensor application using nRF52832 dev kit as a starting point. We have a sensor that we need to read once every second for 10 milliseconds...
I am using the simple code below to generate a signal from a memory buffer. I cannot generate a signal cyclically. If ONE sequence is used, then the buffer is played once...
