Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
I'm trying to get the bmi160 sample to work with my custom nRF9160 board. I think the sample is quite old and not maintained. Unmodified (except fixing pure compilation errors...
Hi.
I am building an I2C driver for the Sensirion SPS30 particle sensor (datasheet: https://no.mouser.com/datasheet/2/682/Sensirion_PM_Sensors_SPS30_Datasheet-1888453...
Hello!
Im trying to change my application. Right now everything works with bonding. DFU and reading and writing characteristics. We have noticed a lot of clients unpair...
Hi all!
I'm trying to run the BLE light switch example on the nRF52833 development board using Segger. I get the following error whenever I try to build the client. This...
sorry where i can find the document/spec for the API that we can use to comunicate with LTE stack L3 . Using Zephyr ? threre are some examples that can help me ?
Best Regards...
Hello everybody, I have to develop an embedded system to acquire and process data. I will be using 2 custom PCBs based on nRF52832: 1- Sensor board: very low power consumption...
Hi Nordic, Please, I am doing a design with nRF52840 and would like to be clear on a few points. Attached is the electrical diagram .
Point 1 For the power supply I am using...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using the RNG functionality with CC310 Library.
When we call this "CRYS_RND_GenerateVector...
Given a 3rd party BLE device (for example a fitness) watch, would it be possible to connect to it using the nRF52 DK and conduct a DFU on it? If so, is there any documentation...
Hi,
I am trying to nrfutil to execute dfu over BLE using nrf52 dk and nrfutil. I have no problems when I try to use nrf_connect mobile app, but I want to use nrfutil desktop...
I want to write my application logs to the flash. I am following this tutorial which is for nrf52: https://jimmywongiot.com/2020/02/24/print-log-flash-log-crash-log-on-nordic...
I want to change the GPIO settings for the pin P1.08 but in the register description (nRF52840_PS_v1.2.pdf) there are only the names and offsets for the pins from P0.00 to...
I've been looking for a DC Motor controller example (for nRF52840) but without luck. Some other users have referred to such an example so I figured it should exist.
Anyone...
I am using SPIM4 with easyDMA in list mode to read a set of registers from an SPI device, and everything seemed to work great until I attempted to use the double buffered...
For some reason I can no longer compile any Zigbee examples.
The errors I am getting are below.
I have no idea what the issue is and I can't find any resources to help...
