Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
sdk version:15.2.0
sd version:6.1.0
platform:pca10040
I have inited three saadc channels , I want to close the specific saadc channel ,but error occured .
The...
Sir,
Using nRF ToolBox for Android.
Our ble device using one of your ble chips sends bytes 0x02, 0xBA
But nRF ToolBox UARTService.java function onDeviceConnected( BlueTooth...
Hey all, my QSPI woes continue. I'm trying write 4 bytes (0xDEADBEEF) of data to a flash chip, equivalent to the NRF52840 DK. I'm using PP4IO and 24 bit addressing mode but...
Hello,
I am using the NRF_LOG_INFO macro to print certain event results. I am writing a large chunk of memory over I2C. The operation succeeds but the log print is only...
Hi All,
I' ve successfully programmed an nRF52840 device with an application running with PHY_CODED modulation and I can scan it from my Samsung Galaxy S+. Unfortunately...
Hi, I'm running nRF5 SDK v15.2, and tried to run the led softblink example on port 1 of a nRF52840, which did not seem to work. I found a problem in low_power_pwm.c, which...
We want to use some device in the peripherial mode.
after the devices were bonded, for next connect I need to hide this advertise packet from air in the nRF Connect util...
We have a problem that we thought was isolated (affecting only one phone) until recently we started getting more phones exhibiting the same issue.
We are Australia based...
I can pair and bond as a Zephyr central via bt_conn_auth_register & bt_conn_security().
When the bond is successful I get a callback to cb_pairing_success(struct bt_conn...
Hello,
I am trying to read the internal temperature sensor using interrupts (SoftDevice is disabled). This is what I have:
#include "nrf_temp.h" #include "nrf_nvic.h"...
I am having hard fault when `nrf_sdh_enable_request` is called in BLE init. I am following BLE_TEMPLATE. I did not copy the solution, I am extending TWI example to include...
Hi,
I am trying to make a micro second timer count and I am using the timer driver from the timer example. However the timer init is failing in my code and I am not sure...
Hello,
I am using pc-ble-driver to write a desktop application interfacing with Nordic connectivity dongle. There is no automatic discovery module functionality so I have...
I am trying to just find what is this LE Secure Connection but can't seem to find anything basic. When i look at the lesc example, it look slike they simply turn the bit on...
