Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi everyone,
I’m working on a Zigbee application using the nRF52840, and I’ve been experiencing periodic reboots that I cannot figure out how to resolve. I’ve already updated...
Hello. I have a question about the development environment when developing using nrf.
When you build a new board and make firmware without using dk or ek, do you usually...
Hello everybody! There is a problem and help is needed. With the help of hardware timers, I need to generate a signal with a given accuracy. The frequency is 998 Hz. I'm using...
We are working on developing wearable device (like band) with cellular-IoT network connectivity. Considering available features and size, nRF91 series seems to be a good choice...
Hello
I am developing an application in which I am using a timer expiry function to submit an event periodically. My application is using the Application Event Manager...
Hello, when testing the BLE sniffer with an nRF52840 dongle (utilizing the most recent official sniffer firmware), I configured Wireshark to capture the coded PHY. After initiating...
Hi there,
I have recently moved to nRF5340 for my audio recording application. I have successfully implemented I2S master on nRF5340 using SPH0465 mems microphone as a...
I have some code that used to compile using version 2.5.2
I'm trying to move to 2.7.0 and have my own manager for TWIM that needs to intercept the TWIM interrupt.
In earlier...
I'm trying to use littlefs in Zephyr with SDK 2.7.0
My code is based on the example project "littlefs" and it compiles without problem using SDK 2.7.0
I'm using nRF Connect...
I am experiencing an issue with my board, where I have interfaced an nRF52840 with an LSM6DSV16 via SPI.
The nRF52840 chip, once started, can decide whether or not to...
I am trying to get an LED attached to GPIO to turn on. I have tried all documented methods I could find but with no success. I have no issue controlling the onboard LEDS but...
Having trouble creating the zephyr DTS DTSI files for i2c0 for the nrf54L15. need to get the initial definition correct,
actually using dtsi
& i2c0 {
compatible =...
Hi everybody. I'm using nRF Connect SDK 2.8.0. I've implemented Zephyr RTOS' core dump functionality on my project. I forced the SoC to write the core dump data on its flash...
I am working on a custom nRF552832 board. I need to use the reset pin (p0.21) as GPIO input.
I am using the NRFConnect plugin on VSCode to develop and program the board...
