Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I have an application running on a custom nRF5340 board that supports simultaneous BLE DFU of the network and application core with MCUBoot. This ticket: seems to indicate...
How can I properly set up the SWD interface for printk on a custom PCB? I have to build my project example and see the message printed on the VS Code console. My custom hardware...
Using nrf5340 as both Central and Peripheral roles and I have implemented the Basic Audio Profile based on the nrf5340 audio example. I am using nRF Connect v2.6.1.
I...
I need a bluetooth module that is capable of simultaneously streaming audio two way, ie two channels stereo out and 1 channel mic in with low latency. A friend had recommended...
Hi folks!
As always, I'll start with relevant environment details
===== Environment =====
nRF Connect SDK v2.5.0 (though not opposed to upgrading to one of the 2.6.X...
Hi,
We are developing a device using nRF5340+nRF7002 running Matter. The problem we have is the code size which is around 900KB when Matter is enabled. This leaves us with...
Hi,
My custom board nRF52840 works as a Peripheral, which advertises itself for connection from a Central.
The project is built based on peripheral_hr sample project....
Dear:
I can upgrade applicaiton ONLY sucessfully through DFU.
but now, i want to upgrade applicaiton+softdeivce+bootloader to deployed devices. do you have such documets...
Hi,
What is the maximum PWM frequency one can achieve on the nrf52840 with 50% duty cycle? Sample .dts and c-code in NRF Connect SDK would be appreciated!
In practice...
HI.
we're developing an application where we need to use 2 UART ports: UART: 0, 2, 3.
Before we added MCU boot in our project everything worked well but after we integrated...
I am working on nrf52832 based custom board and I want system off sleep and wakeup using GPIO pin state change. For that I have configured MCU standby timeout in sdk_config...
I have a thingy91 device and want to implement the following requirements.
Expectation:
NRF9160 should remain in deep sleep mode and on the button click event do the...
I am developing firmware for a BLE peripheral using ncs v2.6.1.
In addition to using the libraries introduced in nRF Connect SDK Fundamentals and BLE Fundamentals on DevAcademy...
Hi,
I am considering to build a line of products using the nRF 5340 product and I am considering the options to perform FOTA.
So far the option I learned from the Intermediate...
