After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Dear Nordic，
We developed a product based on the nRF52833 chip, with an external antenna, 3dBi gain. Use a smartphone to scan the product in the outdoor，the transmission...
The product we are developing will be using a proprietary radio protocol. While in receive or send mode, the radio will either read the Tx data from a buffer via Easy DMA...
Hi,
I'm trying to download hex file to our custom development board which has an nRF5340 on it using the external JLINK on the nRF5340 dev kit. I'm using nrfjprog:
nrfjprog...
Greetings. I am trying to implement a custom cluster with attribute reporting, however, for some reason, i am unable to start reporting of such attributes. I have started...
Hi,
we are developing an application using the nrf42840, Softdevice S140 7.0.1 and nRF5 SDK v16.0.0. We develop the code both on central and peripheral side. So we have...
Hi,
I have two 52840DK,
OS : Windows10 X64
example: \ncs1.7.1\zephyr\samples\bluetooth\periodic_sync\
I didn't change the code, Whether I set [CONFIG_BT_LL_SW_SPLIT...
Hi,
nRF Conncet SDK1.7.1, Windows10 X64.
\ncs1.7.1\zephyr\samples\bluetooth\periodic_adv\,
building and debug work well,and i set the device name "PerAdv", then reload...
Hello
I'm trying to use the example code for ble_app_uart and it doesn't seem to work. I copied the folder for pca10028 and changed processor from nrf51422 to nrf51802 everywhere...
I am using four ADC inputs to the 9160.
I am driving each input from an op amp buffer as in the attached schematic.
ADC channels 0, 2, and 3 work as expected. As for channel...
I am trying to move our existing code based on the recommended NCS SDK. I was able to get MCU boot and SMP working, however, the update is extremely slow. I now seem to be...
I have developed a project using 9160. When I start up with the client board, the log will show that at command execution error occurs when I start up. Why is this? I admit...
Hello nRF community,
I am currently testing some Memfault application that comes with the nRF SDK v1.7.0. I have a custom board designed around the nRF9160 and have been...
Hey,
I'm developing and upgrading a BT mesh to Zephyr 2.7.99 and the base functions work, but my Node keep crashing and I don't know from where. It gives the following...
First off, I see a new changed requirement for making Public tickets:
To raise a public support ticket you need to provide your location in profile. profile Please fill...
Hi Everyone,
I'm having problems getting GPIOTE_IRQHandler_v() to run.
"NRF_GPIOTE->INTENSET = 1" causes my Nano 33 BLE to crash if "(GPIOTE_CONFIG_POLARITY_LoToHi <<...
