Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
I'm performing power measurements with nrf9160-DK running the Serial LTE Modem application.
The example SLM has been modified to add support for HTTP, MQTT and also to relocate...
I have been following the NCS BLE tutorial part 1: Custom Service in Peripheral role - Getting Started - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com) for BLE and...
Hello,
I use nrf52832 and SDK 17.0.2.
I use flash crashlog to store crash log on the flash.
I enabled NRF_LOG_BACKEND_FLASH_START_PAGE = 0, which means flash log area...
Hello,
I have a problem with the GPS and more precisely the AGPS. I would like to retrieve my position with the thingy91, I created a project by taking the AGPS sample and...
So, for a while I have tried to follow these instructions: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hello,
Developing on Zephyr 1.2 and modem fw 1.2.
Developing a client LTE application. If I run the below sequence of commands periodically every 2 min:
eventually...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr.
In this process, I am trying to connect with the sensor API with a "fake" sensor whose...
I'm not certain where to send suggestions, so hopefully this will do...
A very useful addition to the nRF Connect SDK would be support package documentation for Zephyr...
Hi,
I am trying to run the NCS Zephyr ADXL372 sensor sample application (using nRF5340 DK) but get the following error:
This corresponds to the following NACK error: ...
I would like to do mutal TLS on a NRF9160. I found the https sample where the firmware does server authentication. How do I add client side authentication to this example...
I have a project from 3 years ago (2018) that I'm trying to make a simple update to the application code. The code downloads via the Segger Embedded Studio and runs correctly...
A vulnerabilitiy in BLE secure connections is reported as CVE-2020-26558 : Impersonation in the Passkey entry protocol
"The Bluetooth SIG is recommending that potentially...
My application uses a NRF52840 (SD140, SDK 15.2.), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
I'm trying to get a BLE example for NordicSemi nRF52833_xxAA using SoftDevice S113.
I found out only two examples but they don't compile.
Error[Go029]: Variable "sec_mode...
Hello,
Is it possible to disable the antenna pin of the NRF52 in software? I cannot see anything in the data sheet which suggests this.
We are using a third party module...
