Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Dear All,
I would like to know information about QDID for nRF5 SDK for Mesh v4.2.0, we are developing costumed equipment using NRF52833 and we need to start the process...
Dear Nordic support team.
Our product nearly complete Rnd stage.
We face only one thing relate to "Cannot reconnect after unpair device with smart phone".
debug wit...
How can i give command from android device to ble board to get the percentage, temperature, or reset or shutdown the device with the help of receiving command from android...
I'm trying to register the SIM card of the 9160 DK at nRF Connect website,
but the website is always showing "still working..." for more than 15 minutes.
Do you have a...
Hello,
I am experimenting with setting up a network via grouping in the following manner.
Bulb_1 will be put into identification mode, and Switch_1 will detect Bulb_1...
Hello,
I am trying to send gps data using MQTT protocol. For this purpose I wanted to combine MQTT simple example with the GPS example. I added all the methods/dependencies...
Hello,
I started to work witn NRF Connect SDK with nrf52840-dk? I mapped lots of peripherals to NRF Connect SDK. There are no problems. However, I try to map nrf_fstorage...
Hello
I am testing out a blinky FreeRTOS example that's a part of the SDK and would like to use SystemView to visualize context switching and tasks. Are there any steps...
Hello,
We're using a BLE connection configured with a 15ms connection interval, and a radio event notification configured to fire 800us prior to a radio event. I'd like...
Hi,
I trying to create a blank Zephyr project for NRF52 and want to use SES. But I could only open pre-existing samples and there's no way to create a blank project.
Appreciate...
I want to create server and client in nrf9160 not through LTE. only transmit on locally in nrf9160
//prj.conf # enable libs CONFIG_NEWLIB_LIBC=y CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi support team,
In PS, it stated the sensitivities for ideal BLE transmitter, I would like to know:
o Sensitivity at 1M PHY DLE 255 octets , Dirty Transmitter on
o...
Hi,
In the documentation [1] for 802.11.4 for nrf52-sdk it is mentioned that the documentation is for the nrf52840 soc only. Where can I find documentation regarding 802...
I would like to add FOTA via HTTP to mqtt_simple example
please describe how to do that, and how to test the update
I know I need to add the following modules via...
