I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
hello Nordic
recently i encounter a claim that nordic to nordic BLE is faster, or capable of transferring more bits of data per second, then a nordic communicating with...
Hi,
I Have been trying to understand how to flash the nrf9160 IC using SWD and segger. Completed up to the build and run.
Need to know If I make some changes in code...
I am on SDK15.3, NRF52840, armgcc, makefile, console
I need to print a double float number in format of "x.xxxxE-xx". I already know that NRF_LOG can only print float with...
I am using sdk17. I'm implementing central, and I'm using app_ble_out_c to implement it. But there's a problem. This example matches only the specified nus uuid with the service...
Hi, I want to send Door Lock Event Notification commands.
so I modified ZB_ZCL_DOOR_LOCK_SEND_LOCK_DOOR_RES macro in zb_zcl_door_lock.h file.
The result...
hello,
i added scan_rsp_data to add a name on my beacon, but now i cant see manufacturer data on the ble_gap_evt_adv_report_t structure but i can see that perfectly on my...
I'm seeing the modulated output of %XRFTEST offset by approx. 1.675 MHz from the set frequency. Modem version is v1.2.2
Here's my command:
AT%XRFTEST=1,1,1,19500,23...
Hi!
Looking at the schematics for the nRF52833 reference circuitry I see that when USB is used, the VBUS is connected to the C18 capacitor, then GND, and if USB isn't...
I have programmed my device with ble_app_rscs available on nRF5_SDK_15.3.0_59ac345. I was expecting it the main loop
the device will only consume 2 uA however it is consuming...
After a few configuration issues we have finally got a connection with the asset tracker application. However we are not getting far enough to send data.
The log shows a...
Hello,
i am trying the nrfsniffer 3.0, but all the packets seems to being dropped.
I am using:
* BLE400 with nrf51822 module (firmware flashed with stlink )
* Linux...
I am trying to make couple templates for S113 with nRF52832 and nRF52840 with and without FreeRTOS and because there is no such in the examples, I’m not sure I made it right...
Hello,
I'm using SDK for Thread and Zigbee v4.1 and I developed a network using mqtt-sn library. Since the developed application requires data publishing at a high rate...
I want to get logs via RTT (JTAG) in the connectivity firmware example of SDKV15.
I have built the connectivity firmware project using cmake and opened the project in SES...
