Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello, I'm trying to compile the LIBUARTE example from SDK 16 but im getting undefined reference errors, this is what I've done so far:
in sdk_config.h defined , (I've...
Hi, I am really confused about the Nordic SDK and way of doing things... I have seen so much conflicting documentation.
I am using SDK_for_Thread_and_Zigbee_v4.1.0 (currently...
my project is to send pressure data from one device to four other devices, it is medical field, previously i worked in nordic openthread udp protocol using nrf52840 for mesh...
Hello
Created in SDK v17 and simple_timer example. I made a simple code to control the LED using a timer. Every 500 milliseconds, the LED turns on sequentially. LED ON and...
I recently got the nRF52-DK for using as BLE Relay evaluation.
I have downloaded following and installed to run the code
- Segger Embedded Studio (v5.1)
- nRF5_SDK_17...
https://infocenter.nordicsemi.com/topic/nwp_034/WP/nwp_034/nwp_034_intro.html?cp=16_2
download PDF link not working. Perhaps replaced with other white paper(s)?
Thank...
Hello!
I have the following component in my device tree:
I would like to retrieve the PWM device and the associated pin number (pwm1 and 0x14). I tried:
Which...
Hello,
I am trying to develop a firmware to read pulse oximetry and heart rate data from this Sparkfun module (SEN-15219): https://www.sparkfun.com/products/15219
The...
Hi,
We mainly need AWS_Jobs, FOTA, Low Power, GPS, ADC, GPIO, certificate updates and whatever is related.
Currently we working on a project that uses:
- nRF9160 ...
Hi All:
I am trying to develop a project based on Heart Rate example. SDK version is 17.0, the receiver software is based Android-nRF-Toolbox.
Now, I can transfer ADC...
We are observing unexpectedly low throughput on the Mesh GATT Proxy service. Specifically, the Nordic device (acting in the GATT server role) is only sending one PDU on every...
Hi,
I have been looking into connecting two development boards over BT.
Previously, I managed to connect an nRF52833DK to an nRF9160DK.
https://devzone.nordicsemi.com...
Hello,
I am trying to enable the read protection on the NRF51822 on a custom board. By looking through the forums, I found different ways to try and enable the read protection...
