Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hi
I have a question about the new chip nRF52811, it supports AoA direction finding, but it doesn't support Bluetooth mesh?
There's no chip can support both AoA and mesh...
Hello,
I am using the nRF24L01 + circuit on a PCB made according to reference design.
Can I use a 0.5 or 0.6 mm thick PCB? Reference design is made on 1.6mm PCB thick.
I'd like to sniff the BT packets between a remote control and a bed (which is controlled through BT4.2), in order to control the bed through an android application.
Can...
I am using uart to transfer data in a while loop, and it works fine. Now I want CPU to go to sleep mode with sd_app_evt_wait(), and CPU to be waken up via Button then receive...
Hello
I'm working on Smart Remote custom board, which is based on nRF52832.
My Setup is running very well but only when RTT Viewer is connected.(and advertising led is...
I am using the TWI peripheral and want the clock frequency to be 400kHz.
In the data sheet it says for the register setting: 0x06680000 = 400kbps (actual rate 410.256 kps...
Hello All,
I am Facing issue in advertising custom board NRF52810.
I am trying to do the led blinking program on above board.
Using the SDK 15.3 with S112 . The hex...
In Nrf5 sdk V15 their is a micro
ticks = APP_TIMER_TICKS (MS);
My question is what is the maximum value of ms which can be used as input.
the same question goes to the...
Hi, I'm looking for information about duration of peak current on BLE and NFC mode on nRF52840.
Do someone have any answers ?
I saw that peak current on NFC is 80mA max...
Hi
I am using SDK12 with NRF51822,
So far I haven’t initialized the sys_evt_handler ( softdevice_sys_evt_handler_set(sys_evt_dispatch) ) And my program works fine, ...
Hi,
Would you please tell me which timer had been used by ESB and app_timer_init() function?
Which register can I get the current timer count value of above timer?
...
Hi is there an available tutorial for adding multiple custom services for SDK v12 or SDK v15? I've managed to successfully create & use one custom service using bjornspockeli...
Hi,
I'm new to BLE mesh SDK and I'm trying to explore available feature.
I'm referring to Generic on/off application and I would like to increase/ change the advertisement...
Hello.
The other day, I purchased Nordic's BLE module and started developing a multirole program. The development environment is
・Use project:ble_app_multirole_lesc_s132_pca10040...
Hi Nordic team,
I have 2 nRF52 Development kits. I want to use one of them as sniffer.
Please let me know if this is possible.
If possible please let me know where can...
