Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Dear all,
I'm new to Ozone and hope that you will forgive the simplicity of my question.
I'm trying to acquire a simple trace (Code Profile) of the blinky example with...
Hi
I am new to all nordic BLE modules, currently working on nrf52832 eval board. I am trying to scan the BLE Beacons "EDDYSTONE" and their RSSI level for my tracking application...
Dear Nordic
I edit the uuid from sd_ble_uuid_vs_add(&nus_base_uuid, &p_nus->uuid_type), all can success but only one uuid start with 0xFB, when use 0xfb, nrf_app_uart fail...
Hello
I am using SDK 15.3 ble_uart_central and peripheral example.
I am trying to transmit an array of integers from peripheral node to central node. Please help me with...
I need to run gc because I get rc =FDS_ERR_NO_SPACE_IN_FLASH.
So I run gc simple as written in https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0...
Hi all
we used a nrf52832 to communicate over SPI and I2C at the same time with some sensors. This works fine.
At the moment I try to convert the project to nrf52810 but...
Hello,
does anybody now when the sniffer will support coded PHY?
I found a similar questions but no answer yet...
https://devzone.nordicsemi.com/f/nordic-q-a/42216/does...
Hi,
I would like to combine NFC - BLE pairing and launch app record. Naively I thought I would write the second data right after the first:
But this does not work. Reader...
I am using an NRF52832 on an energy harvesting board where lowest power is critical. I can achieve ~2 uA current consumption in idle state (waiting on RTC interrupt), wake...
Hi,
I work on the nRF52840 DK with the ble_app_uart example and I want to add a timer using app_timer api,
in order to create RTC time/date timestamps for my sensors raw...
Hello
I am using SDK15.3 and nrf52832 development board.
In my setup,
1. I have a few peripheral nodes whose only job is to transmit some arbitrary packets ( say P)...
My setup consists of a Raspberry pi and a PCA10056 dev-board (NRF52840). I followed the instruction from here in order to set up the Raspberry pi as boarder router and connect...
Hi all,
I am working on the Smart remote and when "spamming" a lot of key simultaneously, I sometimes get a warning "m_coms : packet lost" and then a disconnection.
...
Hello,
I have a Taiyo Yuden EYSHSNZWZ module. I also had a breakout board manufactured for it to get access to all the pins. I am having trouble trying to program the...
