Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello,
I'm trying to read an ADC value from a sensor(for POC I'll be using a pot wired to 3.3V VDD and GND) but all the examples I found only demonstrated reading the internal...
Hi,
What is your recommended stand-off for your aQFN package to PCB?
Below image is from x-section after mounting nRF52840 to PCB, these are aQFN pads, could you advise...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello to everyonel.
I am working with the Light_switch example of Mesh 3.1 on nRF52832 (PCA10040). At this moment, I am trying to understand how I can send a message from...
Hello!
I want meashure pulse time via input capture.
I configured NRF_P0, NRF_GPIOTE, NRF_PPI and NRF_TIMER1.
It work fine, but in datasheet I found next text: ...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello,
I've got an nRF52832 embedded in a module (Telit RE866). As such, I can't see the markings on the chip and have to resort to reading the FICR registers to identify...
I'm working on a project where two devices are trying to get an estimate of the channel between them by taking RSSI measurements over a period of time. I am having a problem...
Hello,
I have custom board with nRF52840. Most of the time It works on USB power, but it also has a battery. It has some peripherals that powered via USB too (LED w2812b...
I've been trying to add UART support from the uart example to the ble_app_template example. I've enabled all the required drivers and options in sdk_config.h and included...
Hi Nordic,
I am trying to encrypt the advertising data(UUID,Major,Minor,etc.,) of nrf52832 through ECB-AES electronic codebook mode encryption in ctr mode
i had added...
Hello
I am trying to read a multiplexed button matrix, using the BSP button interrupt example. I am doing this on a custom made PCB with an NRF52840 on-board. This is...
