I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi, I'm confused, according to Bluetooth 4.0 Specification bytes are send in Little Endian byte order, and with LSB first in every byte. So when I receive raw data from characteristic...
When running "pip install nrfutil" I get this message - "Could not find a version that satisfies the requirement antlib~=1.0b (from nrfutil) (from versions: ) No matching...
Hi all,
In Nordic SDK ble_app_gls Example , the following UUID is added as part of Advertisement packet
static ble_uuid_t m_adv_uuids[] = /**< Universally unique service...
Hello,
I'm currently building a project for the nRF52 (using SDK 15.2). I need to have 2 ADC channels, 1 for temperature sensor and 1 for battery level. I figured that I...
I want to let nRF9160 communicate through UART with 3.3V logic level, but the logic level is originally 1.8V.
I have been reading nRF91_DK_User_Guide_v07.pdf, but I'm not...
Hello,
I'm working on the implementation of some custom services and I started to question why the SDK implements the service modules as instance managers (as of SDK 15...
We are having an issue with pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ). We're using the nRF52840 dongle. We have compiled and run the `heart_rate_monitor_v6...
Hi,
I want to communicate with a legacy device nrf24l01p+ based using a nrf52840 DK.
Firmware of legacy device setup the card in this way:
I take the esb_ptx esample...
Hi
Getting problem in DFU feature while using segger embedded studio.Device gets programmed successfully but stops working after that.
I am following the same process...
I am looking to check signal strength and would like to be able to do it as easily as possible.
The default asset_tracker sends messages which can be seen in the nrfcloud...
We have an application running on our devices that are using ble_nus to communicate with a base station.
The use case is approximately something like this:
On button presses...
Step1 : init a Client model in Provisoner:
Step2 :config this client:
Step3:set the pub address of this client & control the remote gen_onoff_Server model: but it...
Hi
I've found an issue with the serialization code for the function sd_ble_gap_device_name_get in the SDK 14.1.0. As far as I see the issue still exists in the SDK15.0.0...
Why did Nordic deprecate the -30dBm TX power setting on the nRF52832? The current TX power settings jump from -40dBm all the way up to -20dBm, Why the power jump of 100X?...
HI Nordic Team :
Our important customer uses nRF52832 to develop bluetooth key product . they want to know how long the 52832 enter IDLE mode by calling WFI instruction...
