Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hi,
I have the following lines:
NRF_LOG_ERROR ( "This is an ERROR message." );
NRF_LOG_WARNING ( "This is a WARNING message." );
NRF_LOG_DEBUG ( "This is a DEBUG...
I am inquiring about an issue with the SPIM communication. I am reading the who am i sensor of an MPU9250 and it reads 0x71, as it should most of the time but not always....
uVision V5.26.2.0
Error #541: 'NordicSemiconductor::Device:Startup:8.24.1' component is missing (previously found in pack 'NordicSemiconductor.nRF_DeviceFamilyPack.8.24...
I have a complete implementation of OTA DFU where iOS app performs a DFU to a nRF based BT Device. Now i am implementing a fix for the situation where:
During DFU, if...
Hi,
I am currently having issues compiling the thingy52-mesh-provisioning demo from github with cmake. The Readme talks about using SES to compile it, which works fine,...
Hello, I have read multiple postings on this problem about how you have to "forget" the MCU on your android to reconnect through Bluetooth. This does not fix the problem at...
Hello,
I am having an issue where the nRF52840 dongle does not properly reset. I'd appreciate it anyone can help.
I was evaluating the DFU options, and erased the IC in...
Hi,
I am currently using the nRF52832 and I just recently realized that it does not have USB capabilities. I am building a custom board with this chip and I want to use...
My environment: SDK 15.2, SD 6.1.0, SES 4.12
I can build and run the BLE blinky example on the nRF 52832 DK with no problems. I tested LED on/off by writing to the BLE characteristic...
All,
We have an issue with the data transfer rate between a device that uses a nRF52480 (Rigado-340).
We are sending a number of data chunks, approximately 400, where...
Hello,
Now, I am merging my UART code with the TWI sensor example (I use SDK 13). Now my error after compiling the code is:
In file included from ../../../../../../components...
Hello, i recently used a gateway to sensor example and am unable to revert back to factory program of nrf9160 DK.
I toggled the switch 5 to nrf52840 and flashed the first...
Hello,
I have a problem with MQTT Publisher example on my nrf52832 DK.
1. I am using ubuntu & nordic's SDK15.2.0 for this mqtt example. On raspberry pi 3b I have installed...
Hi,
I'm trying to change the device name of the board. I'm able to write the new name into the characteristic. When the name was written in the characteristic the advertised...
I cannot find the broadcast message when I change to the following code：
/**@snippet [UART Initialization] */ /**@brief Function for initializing the Advertising functionality...
