Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi,
Currently, I use the sdk 12.3.0 on a PCA10028 EVK with the s130 softdevice.
For some reason, I want to change the default location of my application. By default, the...
Hi...,
i have measured round trip delay from client to server.
Now I want to measure total time required to send message from server to client and client acknowledges...
I did current measurement for NRF52840. For mesh light switch demo example measurement was 10 mA, and for Thread CoAP Examples current measurement was 0,6 mA. I don't understand...
Hi all,
I am developing an application for a product where power consumption is critical. The application is bundled with the Secure DFU bootloader. I noticed that the bootloader...
Hello,
I think the question may be more related on how Wireshark works but I plan to do the following:
* use the v2 sniffer firmware and the Nordic Wireshark plugin
...
When I migrated, the reference routine output PWM, but kept reporting errors. I have also changed the relevant definition, but I still can't. Has anyone met it? Thank you...
Hello,
We're evaluating the Laird BL654 using your nRF52840 (to be precise, we're using two DVK-BL654-1.0 development kits).We tried to use the 'blinky' examples (ble_app_blinky_c...
Hi everyone,
I am developing a remote controller using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hello, everyone~
I plan to use the Low Energy Secure Connection funtion with nRF51822. But when I build the lesc example in SDK 12.3.0 (ble_multirole_lesc), there's a error...
Using the sdk15 and softdevice 132 v6, I'm setting up an app to read and write to an SD card that uses SPI1 (SPI0 is used by a display). Everything is working great, except...
Hi,
What's is the max length for the payload data in "mqttsn_packet_sender_publish" method?
EDIT:
Redefining my question above: What's is the max length for the payload...
Hi Sir,
According the table 19.4.2 of 52832 datasheet (v1.4), there is a start up time (0.36 ms) for HXFO.
How do I measure the start up time of my 32M crystal?
If...
Hello,
While an attempt to develop solid security mode bulded around Root of Trust starting from RTL and Device root key we found that unfortunately, it is mentioned in...
I would like to detect if a reset happened due to a brownout or an actual power off.
I tired so far using the GPREGRET and RESETREAS registers. They are useful to detect...
I have an app that works perfectly when run from the debugger, but not when started by HW reset. We use the serial port to communicate to a control processor (STM32) The Nordic...
