I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi, I am trying to make nrf52832 as a UART certal. The service UUID and characteristic UUID of peripheral are shown as the following picture. They are all 128bit and quite...
I'm attempting to implement a simple, GPIO driven interrupt system using SDK15, but I can't seem to find any examples using the nrfx_gpiote driver, or documentation on how...
I am currently working on a master thesis at NTNU, and are working on a sensor system based on audio collection and classification (Machine Learning). Power consumption is...
Hi Support engineer,
I am quite new to Nodicsemi devices, I am going through some getting started tutorials, but I found there is no tutorial based on Segger Embedded Studio...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I need to know that What is the maximum datarate for "ble_app_uart" example ?
In the...
I have a question with flash writing of nRF 52. Once written, you can not write it for the second time. It will not cause an error, but is there any way? Write the source...
Runtime environment:
1.IC:52840QIAA ；
2.SOFTDEVICE:s140_nrf52840_5.0.0-2.alpha_softdevice.hex
Development:
PWM signals of 10 groups of adjustable frequency and...
I am trying to establish communication using SPIM. when I checked the macro definition of NRFX_SPIM0_ENABLED it's present in apply_old_config.h. I am using nrfx_spim driver...
Hi,
I have two 52832 (both on SDK 14.2, S132 v5.1) talking to each other using a slightly modified UART service to support more than one connection.
I have this strange...
Hello,
yesterday I measured the current of our device and found out that it looks more as a square instead of spikes when no device was connected. Found out that when I...
In my code , i use P0.6, P0.8, P1.9 to control three RGB LED.
when I use nRF5_SDK_13.0.0-1.alpha, all is fine,
but when use nRF5_SDK_15.0.0_a53641a, the issure like below...
Hello,
I'm new to Nordic SDK and I would like to ask you for help with change of
GPIO IN_EVENT to GPIO PORT event implementation. The reason is we are using
revision <...
Hi,
I'm using nRF5 SDK v15.0 with S132 v6.0. I have two questions:
1. I use the ble_app_uart example. We want to use high UART baud rate, so I change it to 1M baud rate...
The project I am working on stores information in SRAM while it waits for the radio to get in range and transmit data.
I want to know if I can put items in SRAM buffer that...
