I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi Nordic
I am using ESB_DPL protocol between two 51822 to do RF communication.
First i put two device very close, works very good, no packet loss, then I moved the...
After spending substantial time without luck I will drop my question here.
Setup
nRF5_SDK_12.1.0_0d23e2a -> bootloader_secure debug target
nRF51 & nRF52
IAR...
Hi,
I am using simple ADC peripheral to read internal battery voltage(standalone). I am using two custom nRF51822 boards. One of the nRF51822 board is made by nRF51822...
Hello. I just started learn ble module and some confusing about ble_app_uart:
in file ble_nus.c we have function on_write this function calling when trigerred BLE_GATTS_EVT_WRITE...
I am developing a android app for firmware update on my device. I used buttonless dfu example to switch from application mode to bootloader mode, I write value 0x01 to the...
I'm trying to track down who is erasing and programming 0x800..0xFFF.
Does the SD_MBR_COMMAND_COPY_BL modify 0x800..0xFFF?
I inserted a CRC32 at the end of the MBR ...
How should we comprehend the nature of PPI, when dealing with radio interrupts?
For example, if I point radio event handler call back ( of this type:
static nrf_radio_signal_callback_return_param_t...
Hi!
I want to use UART function in my own project, base on ble_app_template.
but when I remove bsp module & board.h, add my custom pin config file, I can't see any UART...
Hi,
I'm attenting the tutorial to use Eclipse + gcc,
when I try to build the blinky project in Eclipse, I have the following error :
17:19:52 **** Build of configuration...
I am following this tutorial to be able to run the ble_connectovity example on the Nordic: github.com/.../pc-ble-driver
I can build and install Boost and cmake runs successfully...
ba_nRF51_spd.zip Hi,
I use nRF51422, SDK10, SD310 and fstorage fun beacuse I need save 10 uint32_t len datas to flash.
I did that....:
the callback fun
static void...
I have a proximity application where I would like to use the nRF51 DK (PCA10028) and Beacon (PCA20006) with Bluetooth Low Energy. I would like them to automatically link when...
Hi,
With the latest SDK (12) there isn't an UART bootloader example available. Am I right?
I'm trying to understand what are the options to program the nRF51 during...
