Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello everyone,
I am trying to use the ble_app_hrs_rscs_relay example from SDK V11 for s130 (2.0.1).
It compiles and works well when I use an pc10028 evaluation board...
If I have multiple services, 2 for example, how should I set up the srdata.uuids_complete.p_uuids in the code:
ble_advdata_t srdata;
memset(&srdata, 0, sizeof(srdata)...
Hello,
I am developing beacon on nRF51DK and I want to store in non volatile memory some parameteres like:
ProximityUUID
Minor
Majnor
AdvInterval
Tx_power...
Is it possible to configure SPI Master API to send multi-byte words?
My peripheral expects transfers in 16-bit blocks (CS goes low, 16 bits are clocked in, CS goes high...
Hi guys,
I'm going to start the development of a new project based on nrf52832 and I have to decide the firmware architecture and APIs. Designing the support for the Nordic...
I am using a digital microphone using i2S interface with the following signals: BCLK (bit clock), WS (word strobe), SELECT (select for Left/Right) and SDOUT (digital data...
I received that error using master control panel version 3.7.1
While using the last nRFgo Studio (1.21.2) it tells me JLinkARM.dll is not correctly installed. Please run...
Hi! I need to sample and send adc values using ble_nus to read it on an android device. I am using nrf 51DK and SDK version 10.
I tried the below two codes but they are not...
I have a NRF24LE1 transmitter transmitting 10 bytes of static payload every sec.
While I have a Receiver which is NRF52-DK. It is receiving the payload that is sent by...
Hello,
I am working with the nRF52 dev Board and the question arose whether it is possible to interface the nRF52 chip via the virtual com port?
The block diagram in...
Hi, I have problem when change S132 V2.0 to V3.0.
SDK : nRF5_SDK_11.0.0_89a8197
I download s132_nrf52_3.0.0.zip and replace all files in nRF5_SDK_11\components...
I want to know if it is normal to have different hex files after compiling the same project from each one in a different PCs using the same IDE Keil ?
That's really strange...
Hello all:
I am running a nRF52832QF AAB0 pca10040 board with SDK11 in Segger embedded studio.
I followed the 'getting started' tutorial.
After pressing button 1, I noticed...
Hi
is there a possibility to make nrf.exe work under OSX? Is my understanding correct that it is actually written in python, hence, should be portable to mac osx or linux...
