I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
My application uses the nRF51822 with a GPIO configured as output and another GPIO is configured as input. Connected to the GPIO_OUT is a resistive load (Rload) which then...
Hi, we switched from your competition to your platform. I know you wrote somewhere that you cannot provide examples for every sensor out there. But your Nordic Dev Zone is...
I have run many tests using the light_switch demo. I have noticed that occasionally the latency is much larger. The latency jump is between sends, i.e. it will send 20 times...
I am using 3 mobiles for testing
1. One Plus 6
2. Samsung Galaxy Note 8 or Google Pixel
When I connect my hardware with #1 phone and send some data from the nRF Connect...
hello.
i am new to nrf52832
my question is when i press the button it will goes to interrupt handler then turn on the led if i press the same button led will turn off...
LTE link monitor does not work.
OS: Mac SEGGER IDE: v4.16 place: Tokyo in Japan.
I set up the environment from scratch following Get Started Assistant v0.9.2, updated...
Hi,
our installed base of sensors transmit their data in periodic BLE 4.0 beacons. I would like to develop a relay board that receives these beacons, and then retransmits...
Hi,
I want to use the nRF9160 DK for an NB-IoT application. I am located in Bavaria, Germany where there is no LTE-M coverage. I understand that I need the NB-IoT version...
To the kind attention of Nordic support team, from www.nordicsemi.com/ I downloaded all nRF24 Files.
I found very interesting the nRFgo Motherboard (nRF6310 Rev 1.4) pinout...
Hello ,
I am new to nrf52832
i am using external interrupt for led on and off
here the problem is when i press the button 1 led will turned on if i press the same button...
For Zigbee RF manufacture test, we did try nRF52840 using the sample code "radio_test" in SDK nRF5_SDK_15.3.0_59ac345,
but it seems that only the TX power information can...
Hi all,
I'm developing a buttonless DFU based application using the SDK v15.3 Following the documentation was pretty easy and I'm now able to run the app_ble_buttonless_dfu...
Hello All,
I am working on nRF51822. Use nRF51 SDk 12.3.0 version for reference. Writing program in IAR in windows.
Porting the OTA DFU to my custom APP.
use SDK 12...
Hello
I am developing a product by using nrf52840 and s340.
I know the way how to certificate ble. It is using the dtm example.
But I don't know how to certificate...
Hi
I have a question.
I am using USB CDC UART example code for my application development.
I have changed VID and PID in sdk_config.h file as per requirement.
Now...
