Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
Hi,
if my device (nrf52832) is in application and I perform firmware upgrade using nrf connect and PCA10031 on Win 10, the upgrade process is very slow (0.35 kB/s). I stop...
Hello,
I have a following requirements,
Build a custom bootloader which accepts DFU through OTA and UART.
this boot loader must also contain softdevice , so that finally...
I'm having problems with toggling the EXT0 pin on my thingy:52.
I have tried with setting the EXT0 as an output like this: drv_ext_gpio_cfg_output(SX_IOEXT_0); And then...
This is not really a problem - more like an enquiry
Is it possible to gate PWM output using another GPIO pin e.g. if the second pin is low then so its the PWM otherwise...
Hello,
I would like to test and adapt the example "ble_app_uart_coexist" with my nRF52840 DK. Unfortunately, I believe that this one is only intended for nRF52832 and softdevice...
Hello,
I am trying to use the BMD-350 evaluation board to program a standalone BMD-350 module on a custom PCB. I have followed the instructions in the documentation to connect...
Hi,
I'm using custom board with the nrf42840 and I need to use p1.09 as a GPIO.
How can I do this in a debugging mode (using the PCA10056 as a jlink)? Can I get a code...
Hi,
I want to get interrupt on GPIO using gpiote module.
I searched for example but couldn't get it.
Can you guide me how to use gpiote in nRF9160 ?
Regards,
Smitesh...
Using Fanstel BT832A BT 5.0 Module which utilizes SoC nRF52810 QFAA
1) Yes or No: can I configure a GPIO as a Timer/Counter Input so I can feed a high frequency input into...
Hi,
I just wanted to know which flash is used by the flash manager within the SDK Mesh v2.2.0 onoff client/server examples ? Is it the 1MB internal flash or the external...
Hello,
During development of a custom board, based on the BMD-300 module from Rigado, which uses an nRF52832, we ran into a SoftDevice fault under specific circumstances...
Hi,
After trying to work out why one of our nrf9160 DK:s cannot execute any AT commands using the at_client sample I tried redoing the getting started guide to make sure...
Hi, I am making my own bluetooth custom board with nRF52832. Till now, I made my custom pcb following the infocenter layout and chip antenna like below.
Now I want to...
Hello All,
I have 2 evaluation boards nrf53840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in " nRF5_SDK_15.3.0_59ac345 " as following:
A custom...
