E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hello,
I'm trying to read an ADC value from a sensor(for POC I'll be using a pot wired to 3.3V VDD and GND) but all the examples I found only demonstrated reading the internal...
Hi,
What is your recommended stand-off for your aQFN package to PCB?
Below image is from x-section after mounting nRF52840 to PCB, these are aQFN pads, could you advise...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello to everyonel.
I am working with the Light_switch example of Mesh 3.1 on nRF52832 (PCA10040). At this moment, I am trying to understand how I can send a message from...
Hello!
I want meashure pulse time via input capture.
I configured NRF_P0, NRF_GPIOTE, NRF_PPI and NRF_TIMER1.
It work fine, but in datasheet I found next text: ...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello,
I've got an nRF52832 embedded in a module (Telit RE866). As such, I can't see the markings on the chip and have to resort to reading the FICR registers to identify...
I'm working on a project where two devices are trying to get an estimate of the channel between them by taking RSSI measurements over a period of time. I am having a problem...
Hello,
I have custom board with nRF52840. Most of the time It works on USB power, but it also has a battery. It has some peripherals that powered via USB too (LED w2812b...
I've been trying to add UART support from the uart example to the ble_app_template example. I've enabled all the required drivers and options in sdk_config.h and included...
Hi Nordic,
I am trying to encrypt the advertising data(UUID,Major,Minor,etc.,) of nrf52832 through ECB-AES electronic codebook mode encryption in ctr mode
i had added...
Hello
I am trying to read a multiplexed button matrix, using the BSP button interrupt example. I am doing this on a custom made PCB with an NRF52840 on-board. This is...
