I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
I am trying to set up the WDT on a nRF51822, but the timing doesn't seem quite right. If I load the CRV register with a count of 32768 I would expect it to be a one second...
I'm new to Nordic devices and tools. I have experience with Eclipse but I was wondering if there is a guide to help with the creation of a brand new project under Eclipse...
Hi,
As have been discussed earlier there is a problem with iOS device losing CCCD values on reconnect or turning bluetooth ON/OFF.
A patch for the ANCS sample is presented...
Hello Gentlemen,
Is it possible to know the passkey before the BLE_GAP_EVT_PASSKEY_DISPLAY event?
my nRF sensor is set as a display only and my central is an Android...
Hi all,
we are using the nRF51822 together with another module that provides an 1.8V UART only (LO = 0V, HI = 1.8V). Other IC´s on the device are using 3V Vdd and are connected...
I would like to make two BLE single mode devices to communicate with each other and Bluetooth v4.1 supports that, I was wondering if any of Nordic's modules support v4.1?
Referring to page 58 of the reference manual there is a ANAEN control signal that will contect a gpio pin to a corresponding analog input
I am using GPIO P0.01 -> AIN2...
I have started "playing" with the nRF51822 eval kit and the LED-Button example explained in the nAN-36. I wanted to know how is the UART port configured but I have not found...
Is it possible to count pulses with the 51822 from an external device in the range of 250-15.000 pulses pr. second, while the CPU is powered down (softdevice sleep)?
I...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi all,
i am new to nordic and I working on the project to scan/locate iBeacon by using nRF51822,
I can't found a related sample code on SDK 5.2.
Is there something I...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I have built a board using a reference design for the USB dongle board for the NRF24LU1+. Now when I connect to the USB the system identifies the device as "nRF24LU1+ -F32...
