Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Hi,
I am using Zephyr configured to use the softdevice as the BLE controller.
I am looking to read and write a small amount of data to the flash for non-volatile storage...
I use nRFgo Studio 1.21.2.10 and J-Link V5.12f.
In nRFgo Studio I can erase my nrf52. However, programming with softdevice or application ends with error Unable to find...
Hi,
We are having custom HW and having NRF91DK and NRF52.
We have architecture as NRF91 and NRF52 (Central) is connected over UART and NRF52 (Central) and NRF52 (Peripheral...
Hi
I'm using direction finding connectionless_rx project from NRF Connect SDK 1.7.1 with NRF52833 and I want to sample the CTE with a 4MS/s sampling rate (sample spacing...
Hi, I have a project developed on Visual Studio Code and PlatformIO. Now I want to use the same classes with SEGGER Embedded Studio. How do i do? Thanks.
I am very new to this product and Bluetooth technology in general. I am trying to determine what I have done wrong. I have purchased the nRF52 dev kit and downloaded and installed...
Hi,
In our design we use Fanstel BM832 module, based on nRF52832 chip. We have failed spurious emission in ETSI RX mode. Rx LO at ~4958 MHz exceeds the limit by 0.3 dB....
Hi,
We are working on the iOS App development for our BLE device. Our query is that, “we have completed the connection with Ble device with our iOS application on first...
I am using a setup with a PCA10040 with the PPK as piggy back. I also use a JLink Ultra+ connected to the "Debug in" connector on the PCA10040. I have cut the SB20,21,26,27...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I had tried to advertise in TLM format (in temp variable) of eddystone value coming from sensor ssts751 integrated with my devkit but not getting correct. Please suggest me...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough " RSSI > -40 " and initialize...
Hi all,
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My development board acts as a slave, while an app that tries to connect...
Hello,
I'm struggling to understand the available RAM size in that chip.
After reading the product specification v1.7, the RAM specification is described as follow:...
Hi,
1. When nRF5340 has no power supply, adding 3.3V power supply to the digital IO port will produce voltage drop.
2. Why does the voltage drop occur?
3. What is the...
