Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Dear All, I am trying to add a custom service on the ble_template_app that I have managed to run successfully on the nRF52820.
I have successfully created the custom service...
Hi,
I am using the nRF52840 BLE chip and i need to connect the external RTC(M41T62). I have one doubt M41T62 is having the 32khz o/p pin where should i connect that connection...
How does one configure the LF clock source using the new nrf connect SDK ?
(not nRF5_SDK)
I don't see any option for then when doing
west build -t menuconfig
Hello everyone,
I have nrf52840 usb dongle and I want to implement meshSDK/ble_app_uart_coexist example for uart-mesh communication.
I follow all instructions on example...
Let me know How to measure RX Sensitivity by TESCOM TC-3000
My S.W engineer setup TX power +8dBm then He wants to know How can it measure Rx Sensitivity
nRF52840_PS_v1...
Hi
I put the MBN52832 (nRF52832) on my WSM-BL241-ADA-008DK to test the SPI (see the user guide here ).
The sample "peripheral/spi" from SDK ver. 16.0 is used for the test...
Hi everyone I have been trying to use UARTE1 + UART0 combination for a device that i am working on, I have implemented the UART0 using the nrfx_uart library and it works fine...
Hi,
I am using nRF52840 to communicate with the EEPROM. 24AA32AT-I/MC over I2C interface. The TWI scanner example detects the EEPROM address correctly for me .Now, I want...
Hi Team,
We are using nRF9160 DK, we tested that asset tracker application, that was working fine, We also tested the aws_fota (firmware update via AWS) that was also...
I want to develop a mesh network where I can send/receive data from one device to other devices(sleepy sensors) through relay/router node (always on).
For example
A (Publish...
Hi, engineer:
I need to compute FFT on nrf52840, I used sdk-demo fpu-fft, I tested the FFT operation time and found that it took 2 ms，That`s a long time, Did I configure...
Dear all, I have a problem with nRF52811 GPIOTE input interrupt. I have one sensor interrupt pin at GPIO P0.30 with external pull down resistor. I am able to config P0.30...
Hello community,
I have programmed my dongle as beacon. Now I want to stick them to the wall for experiment purposes. How is it possible to power them up via external...
Hello
I am considering a product that connects several NRF52840s to a USB 2.0 7-ch HUB and works with 30 BLE devices. When reviewing a product like this, there are some...
Hi everyone,
I have one question just for confirmation.The available analog pins on nRF52840 DBK are those provided by header P2 (six in total)?
Are there any more available...
