I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi,
With my mistake, the firmware in nrf52840 Dongle is none, Do you know how to get the official firmware? and how to download this firmware? if using Jlink, any pin support...
Hi All,
I have a scanner project based on nrf52840 + S140 and I saw S140 (7.0.0) seems to support nrf52811.
So I want to port existing project to nrf52811 + S140 7.0.0...
Hi, I am experiencing the nrf52832 with some testing and developing few examples.
I am using nrf5_SDK_15.3 SES. OS : Windows 10.
I am using nRF52832 only. I have seen...
When designing an NFC coil to use with the nRF32832, are there any recommendations as to the coil inductance and Q that we should target?
Being a passive design, we are...
Hi I am using the tutorial from https://github.com/bjornspockeli/custom_ble_service_example . I have uncommented some of the starter code from ble_cus.c. My understanding...
I am inquiring about something I know very little about but will try to communicate for the information. Smart phone applications can be opened through a QR code which utilizes...
Hi,
We are using ncs tag v1.0.0.
I am using i2c_scanner example firmware. It works find when used as it is.
When I added "UART2" in this firmware i am getting hard fault...
Using the ble_app_uart example, Using oscilloscope to measure the time interval of broadcasting, two development boards are used respectively. One development board is nrf51422...
Hello, rols and hkn:
I got two different answer about watchdog and hardfault in devzone.
1. watchdog can't reset hardfault. https://devzone.nordicsemi.com/f/nordic-q-a...
https://github.com/bjornspockeli/custom_ble_service_example
I am currently following this example with SES on my NRF52840 DK (PCA10056). I copied the ble_app_template example...
Are there any recommended alternatives (& nordic plugins) to the discontinued Bluetooth Developer Studio? I'm looking for a tool to make the process of creating custom GATT...
Hi! I want to copy data from internal flash to a statically allocated buffer in RAM. I get a DACCVIOL hard fault try to do this by memcpy. The hard fault depends on the number...
I need to send 5 sensor values received over SPI to an app over BLE about 5 times a second. I also need to send a few configuration parameters from the app back to the nrf52...
I am using nRF 52 DK connected to Arietta with ARM Linux (4.2.6) 32 bit.
when I was trying to install "vcpkg" using "./bootstrap-vcpkg.sh", I am getting some errors as shown...
