Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi, I am trying to implement Secure Connection for my application, because using PIN I noticed some problems with the bonding in iOs, in fact using the device manager from...
I've writen a BLE program for a company,they reqire me to certificate the circuit and the program through a Fixed frequency program,what is the hell?Where to get it?
Hello,
[Device: nRF18522 S110 Softdevice 8.0.0 SDK10]
I've referred to this post:
devzone.nordicsemi.com/.../
Does it mean the maximum value is 512 seconds...
hi,For the bluetooth certification, but requires a fixed frequency is 2402 2442 2480 test, could you tell me need how to set up 2442 under the fixed frequency?
I'm trying to make one of the examples in the SDK v9, but I'm stuck on the following error;
L:\NR - nRF firmware\Nordic SDK\V9\examples\ble_peripheral\ble_app_template...
Hi,
I use s110_6.0.0 and sdk_5.2.1 in my old product. I found that I can't write flash sometimes. Timer1 and Timer2 are used, and their interrupt priority level is 1(high_priority...
Hello,
I noticed that their was a question in the developer zone regarding MD bit?
devzone.nordicsemi.com/.../
My question is slightly different. I am using Soft...
Is it possible to use random 128-bit UUIDs for custom services and characteristics? Or do the characteristics in a service need to share 96-bits with the custom service UUID...
The hardware bug #39 on the GPIOTE in EVENT mode which gives a overconsumption of ~1mA even in idle mode on, kills the interest of having a low power chip, because the solution...
I am wondering, for 51422 or 51822, are all radios can work simultaneously or only one type of radio can work at a particular time?
e.g., BLE & ANT can work at the same...
Hi all,
Is it possible to get a callback from the softdevice, when a characteristic is changed? If so can you guide me in the right direction - documentation / examples...
@brief Function for application main entry.
*/
int main(void)
{
// Configure LED-pins as outputs.
LEDS_CONFIGURE(LEDS_MASK);
// Toggle LEDs.
while (true)
{
for...
Hi,
I'm using gazell library with app_pwm.
From documentation gazell use Timer2 and PPI channels 0,1,2.
APP_PWM use Timer0.
When I disable pwm using app_pwm_disable...
Hi,
I'm trying to use the nRF52832DK to flash a Rigado BMD-300 module (nRF52) - I've connected SWDIO, SWCLK, GND and voltage sense to P20.
It seems that because the...
