I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hello, I have been observing some interesting behavior concerning packets sent from server during eDRX idle period. When the period is set to 20.48s or 40.96s, any packet...
I’m writing this post because I’m experiencing a problem with data transmission between two devices—a sensor and a USB dongle connected to a PC—each equipped with a Minew...
Background : To set up a Matter ICD (Internet Connectivity Device) and Thread as a SSD (Sleepy End Device). Here are the detailed settings：
Currently, the Matter over...
Hello,
Before I start to over-develop I need to ensure that there isn't a better solution based on the nPM1300 behavior or capabilities.
Context
I'm using an nPM1300...
Hello,
we are testing the channel sounding performances for distance measurement with the example:
https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
Is there any way to sniff BLE 6.0 packets and see the new content such as channel sounding? I am familiar with the nRF52840 Dongle as a sniffer in Wireshark, is there similar...
Hello all, i made a board with this BLE chip:
nRF52832-CIAA-R
What happens is that when i enable power supply i can see the circuit is properly in advertise ( i can scan...
Hi Nordic,
I want to implement a LED blinking like below pseudo code. I'd like to use Timer x n , GPIOTE, PPI since it doesn't consume any CPU time. for (10 times) { for...
Build configuration is: SDK: nRF Connect SDK v3.0.0 Toolchain: nRF Connect SDK Toolchain v3.0.1 Board target: nrf52833dk/nrf52833
All other values left at defaults.
There...
Hello,
I am currently working with the nRF5340DK and the W5500 shield. Both work perfectly when using the dhcpv4_client application. However, when I attempt to use the recv...
Hello Nordic
Using the old SDK, i was able to do FOTA wiht 10kb/s.
After doing all kinds of tweaks, I am only able to obtain 5kb/s with the new connect SDK.
Can i...
Hello,
I am currently using the nrfutil application to convert modem trace logs to pcaps through an automated process. I am seeing intermittent failures with the following...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
Hello, I am currently developing a testing software to verify whether all the pins of my module have been properly connected. I configured pin 1.03 as a high level in the...
