I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hello,
I want to implement device pairing, using the pairing bit. The pairing bit is set in the masters device type. For a slave to pair with such master, it opens a channel...
Hi Nordic!
I am using nRF UART2.0 and nRF51822.
I am sending some data from nRF51822 to nRF UART2.0
But after 3 minutes, I can get disconnection.
and 0x16 error...
I am currently using ARM's CMSIS-DAP interface to support flashing of an nRF51422 from a host MCU (i.e. to perform updates of the SoftDevice and/or application code running...
Hi guys,
I have a custom hardware with the nrf51822 and we have a slow connection and services discovery is clearly slower that when we run the code in the Development...
I use two nRF24LE1s as transmiter and receiver Here are my questions:
I set the transmiter side to auto reply mode using PIPE0 ,but i found the STATUS regesitor to...
Hi I am trying coding a remote controller using nrf24le1 but failed. any sample code?
it with several keys when push down the pin will connect to GND.
when any key push...
Hi all,
I would connect the NRF8001 module to my microcontroller (SAM3SD8C). Does anyone have an example code for this microcontroller?
Otherwise is possible to modify...
Hi All,
We have a PCA10001 running a ble_app_hid_mouse (modified according to our use case) which receives data from PC UART.
We are trying to connect to this device...
I cannot find any instructions on how to "pair" the nRF8001 with a laptop (I understand that BLE doesn't pair like usual BT).
Are there any tutorials available?!
Thank...
I am trying learn how to handle a central when the bond has been deleted on the device only.
It is a HID device using softdevice7 / sdk6.1, with max 1 bonded centrals....
Hi
I've been able to include Device Manager to bond my peripheral to Master Control Panel, but testing with LightBlue runnining on an iOS 8 iPadI'm having several weird...
Hello, can you provide your design files (schematic and PCB) in ASCII format , so I can load them in my design environment ? Or provide a link to ASCII format ? Thank you...
Hi,
nRF51822 use ESB to communicate with LE1,they both use ACK and retransmit.
In the beginning, 51822 works at RX and it can receive data from LE1;Secondly, 51822 turns...
There is " error: expected identifier or '(' " found on line-8 of header C:\Keil_v5\ARM\Device\Nordic\nrf51822\Include\nrf_delay.h. What's wrong with it?
How do I know...