Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Posting this as separate question as it got no traction in the other thread:
Why are there many of the same include files in the DFU example directory as in the S110 7...
Hi!
I want to send heartbeat messages from 30 servers to 1 client/provisioner.
I can send _HEARTBEAT_PUBLICATION_SET to every server like OpCode = _HEARTBEAT_PUBLICATION_SET...
Hi，
I have searched the posts about how to send/receive more than 255 bytes ,SPI master EasyDMA mode , but still can not find the solution.
I want to know if a ArrayList...
Hi,
i am facing two issue in nRF9160 cellular application.
1.Asset tracker Application:
i loaded Asset tracker example firmware in nRF9160 eval. board. when i run this...
Hello,
I'm porting a project from SDK14.2.0 to SDK15.3.0. Now, all is compiling, i need to figure out why my project is triggering some exception. To help me, i would like...
I am a newbie with nRF Sniffer, which I have installed on one PCA10040 board. I am sniffing communications between a Samsung phone running nRF Connect and a second PCA10040...
Hi,
Here I am trying to use nRF52 DK single board to implement SPIM0(base address: 0x40003000) and SPIS1 (base address: 0x40004000) master and slave communication protocol...
Hello, It is my first time running FreeRTOS on NRF52 and I would really appreciate any help to figure out the root cause for the hard fault. I run a simple FreeRTOS application...
nRF52832_XXAA, S132 v5.0.1, SDK 14.0.0
We enable SoftDevice via nrf_sdh_enable_request(). We immediately assert nrf_sdh_is_enabled() so we know it worked. On the first...
I recently got a custom board manufactured using an NRF52840 with the TI AN043 antenna to find that everything worked except for the bluetooth antenna. So I'm here to seek...
Hi,
I was able to successfully complete Figure 2 on page 6 of nRF_Sniffer_UG_v2.2.pdf, and successfully loaded and ran sniffer_pca10028_1c2a221.hex.
I rebooted my computer...
Hi,
We’d like to migrate from nRF51822 to nRF52 series. We have 2 targets : nRF52811 and nRF52832. We’d rather use nRF52811 (better sensitivity, lower consumption, features...
Hello
I'm trying to send an uint16_t array with 750 elements over the NUS service.
To do so I fill the data in multiplle uint_8 arrays of length "m_ble_nus_max_data_len...
Hi All,
I've got an nRF 52840 PDK and I'm connecting a GPS module ( Adafruit Ultimate GPS Logger Shield ) to it to read the data using nrf_serial.h library. I get about...
Hi
I am working on a project that has two timers, TIMER3 and TIMER4 (TIMER3 as timer and theTIMER4 as a counter). TIMER3 resets after counting up to 4. I am using PPI to...
