I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi，
SDK:ncs2.6.1. The main program runs in the app core, and the net core is included as a child image. The Bluetooth broadcast is normal when tested at room temperature...
I am developing AoA for nRF52833.
Please tell me about antenna switching.
Setting:
PSEL.DFEGPIO[0]=28 PSEL.DFEGPIO[1]=29 PSEL.DFEGPIO[2]=30 PSEL.DFEGPIO[3]=31
SWITCHPATTERN...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
I have made my own NRF52832 Dev board as in the next image:
I received the board, and ICs and hand-soldered them in my home.
however, I am still a newbie in nRF SDK...
I been trying to figure this out but to no avail. I get these errors on build.
:/ncs/toolchains/b620d30767/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi...
Using the "launcher" the open button appears to do nothing and the update from V4.2.0 to V4.2.1 produces an error message.
Twice I have uninstalled V5.1.0 and replaced it...
I'm using an nfr52840 board.
I noticed that when using The 'zephry-sdk' v3.5.99-ncs1-1, when doing a passive scan using:
BT_LE_SCAN_ PASSIVE
which sets:
BT_LE_SCAN_PARAM...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message with a something hits the device. To achieve this...
I am working off of the NRF SDK Zephyr repository where I am using the NRF Security subsystem in order to use PSA for AES encrypt/decrypt. I need additional ciphers such as...
To output PWM signal as early as possible after powering on the NRF5340DK, I added the same code in mcuboot/boot/zephy/main.c and mcuboot.overlay as in the app core. This...
I reference the sample at https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise-3-interfacing...
I have a packet that I am sending out using the nrf52840. Using another piece of code supplied by Emil Lenngren, information from the solar_sensor_beacon project and raw data...
Hi,
I am using the NRF52840 dongles for BLE communication with S140 and the NRF5 17.1.0 SDK. I have plugged each dongle in a Raspberry Pi 3B+, and have set the DCDC regulator...
Using the LVGL sample... The sample LVGL code works on nrf52840dk but not the RAYTAC MDBT50Q . I hope I'm just missing something obvious?
Flash blinking to nrf52840dk...
