I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Hello
I'm using SDK 15, S132 PCA10040
I have followed this tut.
I've tried 2 scenarios which in both I get error value:
1. when advertising_init() is before services_init...
Hello,
I saw this , but I was struggling with the merge for quite a long time now. Is there any ready example for e.g. provisionee or provisioner from light_switch merged...
Hi, Nordic!
I wanna know how change characteristic(service,Rx,Tx) UUIDs .
For example,
Proximity UUID : 01020304 -0506-0708-0910-111213141516
Service UUID : 01020304...
Hi,
I'm trying to merge central/peripheral example "ble_app_hrs_rscs_relay" with "ble_app_buttonless_dfu", and get error while compiling ‘ble_dfu_unbonded.c’:
I've included...
Hello I originally wanted to use esb_ptx/esb_prx but the packet could not be changed to 128 bytes! Compressing data packets is inconvenient! I use radio to achieve my project...
I am using Segger Embedded Studio and the nrf52840 development kit.
I can run the BLE peripheral examples using SDK 15 and s140 V6 "blinky" and " cscs" .
but the ble_app_rscs_pca10056_s140...
Checking if this is possible and how to complete.
For the ble_app_beacon example, I'm able to reuse #define APP_DEVICE_TYPE 0x02, to be #define APP_DEVICE_TYPE 0x0E, 0x06...
Hello ,
we are new to BLE
1. We make a long life temp and light sensor , just only transmit from the Nrf to mobile (one way ) , we would like :
1.1 sensor always be...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
Hello,
For my project, I want to be notified when my device changes the value of my characteristic so i used the HealthThermoDemo example.
here is my code :
But despite...
Hi , I want to use two GPIO oin with button press hadler even . when pin low will interrupt and into handle..
Below is the code for the single key.
Thanks.
Pa...
This is somewhat of a continuation of this topic:
What does APP_BLE_CONN_CFG_TAG do?
Softdevice 132, header: ble.h: SVCALL(SD_BLE_CFG_SET, uint32_t, sd_ble_cfg_set(uint32_t...
I'm using RFduino that utilizes nRF51822. I need to set a timer1 as timer0 is used by the BLE stack, so I used the following code:
#define TRIGGER_INTERVAL 1000 // ms...
Hello,
Today I had a case where I tried to perform a bootloader-only DFU on a device with a debug version of the bootloader, but instead of trying to replace it with another...
Hi Technical team,
I want to use nrf52832 for my project, below are the some doubts i have with nrf52832
1) nrf52832 will act as HUB and receive data from peripheral...
