Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
1. Hi i am utilizing nrf52840 sdk with ver 17.1.10 s140 and i have the central UART as main app from there we are calling bootloader
2. Before calling bootloader ble dfu...
I tried to use mcumgr to write and read files to the littlefs of 9160. According to the instructions, I will enter mcumgr conn add acm0 type="serial" connstring="dev=/dev...
Hi are there any image/bulk data transfer demo to test throughput between nRF and iOS application
There is one for older nRF5 SDK but couldn't find one for nRF connect ...
Hi,
I use two nRF52833-DK boards for uart communication (both using pin p0.06 for TX and p0.08 for RX), with their TX and RX and GND pins connected to each other, and perform...
Hello
I am facing issues while pairing nRF7002DK with nRF WiFi provisioner app, when I build the app (provided by nordic and hosted on github). However the pairing is successful...
Hello. On july 26 at the same hour, about 30 of our cellular modems stopped sending data. They are all using Verizon firmware. The units using Hologram firmware are still...
Hi
I have 2 BLE boards with some environment sensors on them.
I need to synchronise the 2 boards with < 1 mili second precision.
one board is configured as central,...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
Hello,
We are using Zephyr OS and SDK v2.5.0 on nrf52840 chip. We have noticed some delay between spi_write and spi_read of 29µs,which is critical for our goal. Comparing...
After I installed nRF Connect SDK 2.7 and tried to run the pre-release version of VS Code extension, I am now compleatly unable to make nRF Connect for VS Code function. ...
I' m using custom board of nrf5340 with nrf7002, and the SDK version is ncs v2.5.2.
I've tried to build and run, but the log in RTT viewer is only print the line "Bringing...
Hi nordic:
I am currently using NRF52833 to create a MESH product and would like Bluetooth to send AOA tag information in MESH mode. Is this feasible?
Best Regards ...
I encountered the following error while building my ZigBee app on a CI (dockerized Linux container), after bumping the SDK from 2.6.1 to 2.7.0.
The part "nRF52840" in...
Hi All, I am using an nrf52832 and using NCS version 2.6.0. I am having an issue where I am trying to initialize and run a thread, but the thread never runs. I have tried...
I want to set the CONFIG_CAF_BLE_ADV_FAST_ADV Kconfig option to make the Peripheral initially advertise with a shorter interval,but after adding some dependency configurations...
