Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
For me it is confusing how the Nordic's exercise and sample apps handle the state of CCC descriptor value.
Adding notification and indication support
Why do we need to...
Hi,
I am using https://github.com/NordicDeveloperAcademy/nRF-Connect-SDK-Fundamentals lesson5/fund_less5_exer1. I am able to receive UART message using default UART RX P0...
Hello we are using custom board nrf52840 with nRF SDK 15.2.0 on SEGGER Embedded Studio
I hope someone can help me with this issue. I am using SPIM3 to communicate with the...
We've been having an issue with certain tablets running Android 14 apparently getting into a state where all connection attempts result in a GATT 133 error. When it's in this...
Hello everyone, I am working on an app where we use I2S driver for ws2812 LED strip to signalize status of our app. When I try to signalize status while starting BLE and starts...
Hi,
I'm using Zephyr controller instead of Nordic's Softdevice to use the DTM HCI feature in the Zephyr controller. Before switching to Zephyr controller, the application...
I want to be able to select the Network Coordinator Zigbee channel based on some GPIOs state (switches).
Is there any api function to set CONFIG_ZIGBEE_CHANNEL at runtime...
I am use sample "Bluetooth: Peripheral HR" as the base app
and added these settings to `prj.conf` on both central and peripheral sides
but I still got the...
Hello everyone, currently I am writing a program to read the SCD41(I2C) sensor and then use BLE to transmit information. With a separate program in twi_sensor, I see that...
Hello nRF team. Is there any different bewteen passing AT command and directly calling the Modem lbraries APIs(from nRF Connect SDK v2.5.2) to control the modem? For example...
Currently our product shipped with SD132 7.0.1, and bootloader/dfu compiled with SDK 16.0.0
We are testing update the bootloader on production devices, and want know how...
Hi Team, I am trying to do DTM test in NRF 52840 using Zephyr- os .The DTM code is working fine on my dev kit ( NRF 52832).I compiled DTM code for NRF 52840 and changed the...
Hi,
I have a problem with sending over NB-IoT to a cloud service. I have found that the helt of my messages only arrive in the AWS cloud and it seems like the modem also...
Hi Support Team
We use ncs to develop nRF52840 application and want to know how many low power mode do ncs have and how to enter these low power mode.We want the nRF52840...
Hello,
We are searching for a board that supports Angle of Arrival(AOA) and Angle of Departure (AOD) for conducted mode radio testing.We need a board euipped with an antenna...
