I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I have a similar question as in the previous post (about 4 years ago) with title "nRF52 WLCSP DCC routing - - ok to run over GPIO pins?" by Laserdan, i.e., I would like to...
Hi there,
The spec for nRF52840 says in sec 6.33.1 that for UART, "The external crystal oscillator must be enabled to obtain sufficient clock accuracy for stable communication...
Hi,
How do you export your project from nRF Connect within VSC? You may have modifications you did for DTS files, prj.conf etc, that you may miss if you focus on just src...
Hello,
The documentation for the nRF5340 says that the UICR OTP registers can only be written to a non-0xFFFF value a single time: > Can only be written to a non 0xFFFF...
HI,
In our application, there is strange dependency for BLE service. The device is getting detected on ble scan only if we flash the ble application after flashing an application...
Hello,
with iOS 16 the connection during the update of the Firmware with IOS-DFU-Library not working. It is stop after few second with the error 202.
Do you know any solutions...
Hi, I restart advertising with ble_advertising_start and sd_ble_gap_adv_stop because I need to change the advertising interval in different situations. I am observing high...
I use nRF Connect for Desktop v3.12.0 (the latest) and its apps:
Bluetooth Low Energy (the latest standalone application v4.0.0)
Programmer v3.0.4 (the latest)
Can...
Is there support now for coded phy on nrf ble sniffer?
I'm using the nrf52840 devkit (hardware version 2.0.2 which supports coded phy) and sniffer works fine without coded...
It looks like the BT Mech spec has not been updated since 2017. Is there an update in progress and is Instaburst (or similar function) a candidate feature?
This would seem...
Hi,
I am facing a peculiar problem, wherein my application has two threads as in below:
Thread-1: is a preemptive thread which has UART functionality, along with UART...
I'm trying to run uart secured bootloader example in folder: @NRF5_SDK\examples\dfu\secure_bootloader\pca10040_uart_debug
but it doesn't work.
My setting is:
base...
Hi all!
I have created a simple application that only turns on a led and power it off using BLE in NRF52810. The thing is that simple app uses a huge RAM (~85%) and flash...
Hello,
I turned on the flash protect function through the CONFIG_FPROTECT switch, and the system kept running until spm_config_flash restarted.
Flash protect code in...
