Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi team,
I'm developing BLE keyboard and i'm interfacing keyboard with nRF52832 using Zephyr RTOS .
I have example code in SDK, I'll share the path " manthan@man:~/ncs...
Hello!
I'm trying to set up data transfer between nRF 52840 dongle and KX134 accelerometer from SparkFun. Currently I'm running the WHO_AM_I test only. The code is derived...
Hi all,
What's happening?
System reboots when "flash_erase" is called with parameters offset 0x1f000 and size 0x1000
Setup:
NCS v2.0.0
nRF52832 with 512K flash...
Hello,
Been chasing this undefined reference to `__device_dts_ord_XXX' issue around for awhile now with no clear path forward. What I am observing is extremely similar to...
Hello,
I am working on Thread client server based network. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development hardware is nRF52840-DK, HW Version 2...
Hi,
I am using nrf toolchain v2.0.0, and am testing the dfu-ota example over BLE by following the below link ( ) . howveer for fast boot up, i am using "
CONFIG_BOOT_VALIDATE_SLOT0_ONCE...
It is possible to change the partition table through a FOTA?
Is the partition table stored somewhere on the device, or is it merely used for linkage? If it is linkage only...
Does anyone know how to use the CMSIS-DSP FFT library on a nrf52832?
I am using the nrf Connect SDK and it seems all of the examples are for nrf5 SDK.
I am looking to...
i use the ubuntu20.04 and open nrfconnect-3.11.1-x86_64.appimage through proxy successfully
then i install and open the toochain manager , there is not include NCS 2.0...
We are developing a new product and plan to use nRF52810. As I understand nRF52 will be supported for production in the new nRF Connect Release (1.3.0) that will come soon...
Hello,
Our application requires the device to go into deep sleep and wake up every 24Hr or on the Accelerometer interrupt. We were able to obtain the sleep mode and wake...
I'm trying to migrate my project to NCS 2.0.0 but having an issue like below:
c:/ncs/toolchains/v2.0.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/10.3...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi We have designed some boards with ESPRESSIF WiFi BLE Module ESP-32-WROOM-32E for control and monitor.
Is it possible to connect esp32 to nRF21540 to extend range ( such...
Hi, I am using nRF52840 and communicating with Simcom GSM( Sim7600g ). 1- Is there any example code/ Library to connect with the MQTT server?
2- Can I use this example code...
