Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hello,
could you please tell me how to configure the Hardware Chip Select Funtionality for SPIM3. I am developing a communication between a sensor and the NRF via SPI transfers...
Hello everyone,
I am currently using NRF5340dk and I need the Library queue, (I especially need the functions: nrf_queue_push and nrf_queue_pop..). (Knowing also that I...
Hi Nordic Team, I am trying to develop an AOA application using the NRF52833 nordic SOC. I am using NCS 1.6.1 development SDK in Segger Embedded Studio.
I am flashing a...
Hi
I want to measure the battery lithium, this battery is the principal source (3.7v 300mh), the maximum voltage is 4.2 when the charge is full,
i'm using this code for...
Hi
I'm trying to enable BLE host-only build on Application core on nrf5340dk, and also enable RPMsg/openAMP.
I'm using Zephyr and its build system.
I get the following...
Hello everyone,
I'm working on a project right now and I want to use the ADS1298 analog to digital converter and configure it with NRF5340dk. Being a beginner I looked for...
hello,
i'm having an nrf52 based system with an antenna switcher in front of it, for antenna diversity. i tried using BT_HCI_OP_READ_RSSI as basis for my antenna diversity...
Hello, All;
Using your nRF9160 chip to develop, there are some questions when using the network and positioning, Hope to get your answer:
1. Can LTE work at the same time...
Hello,
I have two projects, one for the application core (modified BLE Peripheral sample) and the second is for the network core (modified HCI_RPMsg sample). I am currently...
Hi all:
condition:
SDK14.2
PCA10040
example: ble_app_uart_c
I have a central device ,it need to scan RSSI value of peripheral.
If the RSSI is more than threshold...
Hello,
we were using the HRS example as a starting point and modified it for our application. Everything works fine, we can see our custom characteristics, control our device...
Is it possible, without having to join ZOI, to recompile the Zigbee ZBOSS NCP Host for the Raspberry Pi?
The NRF Connect SDK documentation under ZBOSS NCP Host states :...
Hello,
we have an custom made board with a module from raytec MDBT42q.
Our application based on the nus example.
On port 0.7 we have a led.
It seems, that there is...
Hi
How do I configure a custom child image for the network core on nrf5340dk? We're using Zephyr RTOS, and want to do a multi image build when building the application ...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
